I had to send the Cisco 899 4G LTE router to Australia since there's a project for a remote site to have a temporary Internet access. I previously setup the same router on my previous
blog using SingTel and M1 4G SIM cards. The Testra and Optus
APN settings
can be found on this
link. Only the LTE profile configuration was changed on the router.
Router#cell 0 lte profile create 1 telstra.internet none ipv4
Warning: You are attempting to modify the attach profile.
Please consult the service provider before doing so.
Modem power cycle required for change to take effect.
PDP Type = IPv4
Access Point Name (APN) = e-ideas // FROM PREVIOUS SINGTEL LTE TESTING
Username = 65ideas
Password = 65ideas
Authentication = CHAP
Profile 1 already exists with above parameters. Do you want to overwrite? [confirm]
Profile 1 will be overwritten with the following values:
PDP type = IPv4
APN = telstra.internet
Authentication = NONE
Are you sure? [confirm]
Profile 1 written to modem
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface cell 0
Router(config-if)#ip address negotiated
Router(config-if)#ip nat outside
Router(config-if)#encapsulation slip
Router(config-if)#dialer in-band
Router(config-if)#dialer idle-timeout 0
Router(config-if)#dialer-group 1
Router(config-if)#
*Apr 18 06:10:48.907: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI0, changed state to up
Router(config-if)#dialer-list 1 protocol ip permit
Router(config)#
Router(config)#access-list 1 permit 10.1.1.0 0.0.0.255
Router(config)#
Router(config)#ip route 0.0.0.0 0.0.0.0 cellular 0
Router(config)#ip nat inside source list 1 interface cellular 0 overload
Router(config)#interface vlan 1
Router(config-if)#no shut
Router(config-if)#ip address 10.1.1.1 255.255.255.0
Router(config-if)#ip nat inside
Router(config-if)#
Router(config-if)#end
Router#show cellular 0 radio
Radio power mode = ON
Channel Number = 4412
Current Band = WCDMA 850
Current RSSI(RSCP) = -91 dBm
Current ECIO = -13 dBm
Radio Access Technology(RAT) Preference = AUTO
Radio Access Technology(RAT) Selected = UMTS ( UMTS/WCDMA )
Router#show cellular 0 network
Current System Time = Mon Apr 18 6:12:45 2016
Current Service Status = Normal
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Network = Telstra
Mobile Country Code (MCC) = 505
Mobile Network Code (MNC) = 1
Packet switch domain(PS) state = Attached
Location Area Code (LAC) = 30802
Cell ID = 61079747
Router#show cellular 0 profile
Profile 1 = INACTIVE* **
--------
PDP Type = IPv4
Access Point Name (APN) = telstra.internet
Authentication = None
Profile 2 = INACTIVE
--------
PDP Type = IPv4
Access Point Name (APN) = e-ideas
Authentication = CHAP
Username: 65ideas
Password: 65ideas
* - Default profile
** - LTE attach profile
Configured default profile for active SIM 0 is profile 1.
Router#show cellular 0 all
Hardware Information
====================
Modem Firmware Version = SWI9X15C_05.05.58.00
Modem Firmware built = 2015/03/04 21:30:23
Hardware Version = 1.0
Device Model ID: MC7304
Package Identifier ID: 1102029_9903299_MC7304_05.05.58.00_00_Cisco_005.010_000
International Mobile Subscriber Identity (IMSI) = 505013486352123
International Mobile Equipment Identity (IMEI) = 352761060732456
Integrated Circuit Card ID (ICCID) = 89610185000889479789
Mobile Subscriber Integrated Services
Digital Network-Number (MSISDN) =
Current Modem Temperature = 43 deg C
PR ID = 9903299, PRI version = 05.10, Carrier = 1
Profile Information
====================
Profile 1 = INACTIVE* **
--------
PDP Type = IPv4
Access Point Name (APN) =elstra.internet
Authentication = None
Profile 2 = INACTIVE
--------
PDP Type = IPv4
Access Point Name (APN) = e-ideas
Authentication = CHAP
Username: 65ideas
Password: 65ideas
* - Default profile
** - LTE attach profile
Configured default profile for active SIM 0 is profile 1.
Data Connection Information
===========================
Profile 1, Packet Session Status = INACTIVE
Profile 2, Packet Session Status = INACTIVE
Profile 3, Packet Session Status = INACTIVE
Profile 4, Packet Session Status = INACTIVE
Profile 5, Packet Session Status = INACTIVE
Profile 6, Packet Session Status = INACTIVE
Profile 7, Packet Session Status = INACTIVE
Profile 8, Packet Session Status = INACTIVE
Profile 9, Packet Session Status = INACTIVE
Profile 10, Packet Session Status = INACTIVE
Profile 11, Packet Session Status = INACTIVE
Profile 12, Packet Session Status = INACTIVE
Profile 13, Packet Session Status = INACTIVE
Profile 14, Packet Session Status = INACTIVE
Profile 15, Packet Session Status = INACTIVE
Profile 16, Packet Session Status = INACTIVE
Network Information
===================
Current System Time = Mon Apr 18 6:12:45 2016
Current Service Status = Normal
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Network = Telstra
Mobile Country Code (MCC) = 505
Mobile Network Code (MNC) = 1
Packet switch domain(PS) state = Attached
Location Area Code (LAC) = 30802
Cell ID = 61079747
Radio Information
=================
Radio power mode = ON
Channel Number = 4412
Current Band = WCDMA 850
Current RSSI(RSCP) = -91 dBm
Current ECIO = -13 dBm
Radio Access Technology(RAT) Preference = AUTO
Radio Access Technology(RAT) Selected = UMTS ( UMTS/WCDMA )
Modem Security Information
==========================
Active SIM = 0
SIM switchover attempts = 0
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of CHV1 Retries remaining = 3
GPS Information
==========================
GPS Info
-------------
GPS Feature: enabled
GPS Port Selected: Dedicated GPS port
GPS State: GPS disabled
SMS Information
===============
Incoming Message Information
----------------------------
SMS stored in modem = 1
SMS archived since booting up = 0
Total SMS deleted since booting up = 0
Storage records allocated = 25
Storage records used = 1
Number of callbacks triggered by SMS = 0
Number of successful archive since booting up = 0
Number of failed archive since booting up = 0
Outgoing Message Information
----------------------------
Total SMS sent successfully = 0
Total SMS send failure = 0
Number of outgoing SMS pending = 0
Number of successful archive since booting up = 0
Number of failed archive since booting up = 0
Last Outgoing SMS Status = SUCCESS
Copy-to-SIM Status = 0x0
Send-to-Network Status = 0x0
Report-Outgoing-Message-Number:
Reference Number = 0
Result Code = 0x0
Diag Code = 0x0 0x0 0x0 0x0 0x0
SMS Archive URL =
Error Information
=================
This command is not supported on this platform.
Modem Crasation
===========================
Modem crashdump logging: off
Router#show interface cellular 0
Cellular0 is up (spoofing), line protocol is up (spoofing)
Hardware is 4G WWAN Modem - Global (Europe & Australia) Multimode LTE/DC-HSPA+/HSPA+/HSPA/U
Internet address will be assigned dynamically by the network
MTU 1500 bytes, BW 9 Kbit/sec, DLY 100000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation SLIP, loopback not set
Keepalive not supported
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/10 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=down DSR=down DTR=down RTS=up CTS=up
Router#debug chat
Chat scripts activity debugging is on
Router#debug modem
Modem control/pr activation debugging is on
Router#debug dialer
Dial on demand events debugging is on
Router#debug cellular 0 messages callcontrol
*Apr 18 06:18:16.943: TTY0: resume timer type 1 (OK)
*Apr 18 06:18:16.963: TTY0: pause timer type 1 (OK)
*Apr 18 06:18:16.963: TTY0: resume timer type 1 (OK)
CALLCONTROL debugging is on
Router#
Router#
*Apr 18 06:18:19.035: TTY0: pause timer type 1 (OK)
*Apr 18 06:18:19.035: TTY0: resume timer type 1 (OK)
Router#
Router#ping 8.8.8.8
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 360/435/656 ms
Router#traceroute 8.8.8.8
Type escape sequence to abort.
Tracing the route to google-public-dns-a.google.com (8.8.8.8)
VRF info: (vrf in name/id, vrf out name/id)
1 * * *
2 * * *
3 Bundle-Ether14.wel-edge901.perth.telstra.net (139.130.16.49) 180 msec 212 msec 248 msec
4 bundle-ether6.wel-core3.perth.telstra.net (203.50.6.214) 220 msec 208 msec 240 msec
5 bundle-ether7.fli-core1.adelaide.telstra.net (203.50.11.18) 232 msec 236 msec 252 msec
6 bundle-ether9.win-core10.melbourne.telstra.net (203.50.11.91) 240 msec 268 msec 256 msec
7 bundle-ether12.ken-core10.sydney.telstra.net (203.50.11.122) 268 msec 268 msec 300 msec
8 bundle-ether1.ken-edge901.sydney.telstra.net (203.50.11.95) 300 msec 268 msec 260 msec
9 google6.lnk.telstra.net (58.163.91.202) 320 msec 260 msec 248 msec
10 216.239.40.223 240 msec 240 msec
216.239.41.77 280 msec
11 209.85.251.53 268 msec
216.239.41.79 260 msec
209.85.244.15 248 msec
12 google-public-dns-a.google.com (8.8.8.8) 272 msec 248 msec 288 msec
Router#show cellular 0 radio
Radio power mode = ON
Channel Number = 4436
Current Band = WCDMA 850
Current RSSI(RSCP) = -88 dBm
Current ECIO = -6 dBm
Radio Access Technology(RAT) Preference = AUTO
Radio Access Technology(RAT) Selected = UMTS ( UMTS/WCDMA )
Router#show cellular 0 radio
Radio power mode = ON
Channel Number = 4436
Current Band = WCDMA 850
Current RSSI(RSCP) = -88 dBm
Current ECIO = -6 dBm
Radio Access Technology(RAT) Preference = AUTO
Radio Access Technology(RAT) Selected = UMTS ( UMTS/WCDMA )
Router#show cellular 0 network
Current System Time = Mon Apr 18 6:26:49 2016
Current Service Status = Normal
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Network = Telstra
Mobile Country Code (MCC) = 505
Mobile Network Code (MNC) = 1
Packet switch domain(PS) state = Attached
Location Area Code (LAC) = 30802
Cell ID = 61079744
Router#show cellular 0 radio
Radio power mode = ON
Channel Number = 4436
Current Band = WCDMA 850
Current RSSI(RSCP) = -88 dBm
Current ECIO = -6 dBm
Radio Access Technology(RAT) Preference = AUTO
Radio Access Technology(RAT) Selected = UMTS ( UMTS/WCDMA )
Router#show cellular 0 network
Current System Time = Mon Apr 18 6:26:49 2016
Current Service Status = Normal
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Network = Telstra
Mobile Country Code (MCC) = 505
Mobile Network Code (MNC) = 1
Packet switch domain(PS) state = Attached
Location Area Code (LAC) = 30802
Cell ID = 61079744
Router#show cellular 0 profile
Profile 1 = ACTIVE* **
--------
PDP Type = IPv4
PDP address = 10.106.18.202 // DHCP AND DNS IP AUTO LEASED BY TELSTRA
Access Point Name (APN) = telstra.internet
Authentication = None
Primary DNS address = 10.5.80.241
Secondary DNS address = 10.5.68.232
Profile 2 = INACTIVE
--------
PDP Type = IPv4
Access Point Name (APN) = e-ideas
Authentication = CHAP
Username: 65ideas
Password: 65ideas
* - Default profile
** - LTE attach profile
Configured default profile for active SIM 0 is profile 1.
Router#show cellular 0 all
Hardware Information
====================
Modem Firmware Version = SWI9X15C_05.05.58.00
Modem Firmware built = 2015/03/04 21:30:23
Hardware Version = 1.0
Device Model ID: MC7304
Package Identifier ID: 1102029_9903299_MC7304_05.05.58.00_00_Cisco_005.010_000
International Mobile Subscriber Identity (IMSI) = 505013486352123
International Mobile Equipment Identity (IMEI) = 352761060732456
Integrated Circuit Card ID (ICCID) = 89610185000889479789
Mobile Subscriber Integrated Services
Digital Network-Number (MSISDN) =
Current Modem Temperature = 43 deg C
PRI SKU ID = 9903299, PRI version = 05.10, Carrier = 1
Profile Information
====================
Profile 1 = ACTIVE* **
--------
PDP Type = IPv4
PDP address = 10.106.18.202
Access Point Name (APN) = telstra.internet
Authentication = None
Primary DNS address = 10.5.80.241
Secondary DNS address = 10.5.68.232
Profile 2 = INACTIVE
--------
PDP Type = IPv4
Access Point Name (APN) = e-ideas
Authentication = CHAP
Username: 65ideas
Password: 65ideas
* - Default profile
** - LTE attach profile
Configured default profile for active SIM 0 is profile 1.
Data Connection Information
===========================
Profile 1, Packet Session Status = ACTIVE
Cellular0:
Data Transmitted = 2893 bytes, Received = 5404 bytes
IP address = 10.106.18.202
Primary DNS address = 10.5.80.241
Secondary DNS address = 10.5.68.232
Profile 2, Packet Session Status = INACTIVE
Profile 3, Packet Session Status = INACTIVE
Profile 4, Packet Session Status = INACTIVE
Profile 5, Packet Session Status = INACTIVE
Profile 6, Packet Session Status = INACTIVE
Profile 7, Packet Session Status = INACTIVE
Profile 8, Packet Session Status = INACTIVE
Profile 9, Packet Session Status = INACTIVE
Profile 10, Packet Session Status = INACTIVE
Profile 11, Packet Session Status = INACTIVE
Profile 12, Packet Session Status = INACTIVE
Profile 13, Packet Session Status = INACTIVE
Profile 14, Packet Session Status = INACTIVE
Profile 15, Packet Session Status = INACTIVE
Profile 16, Packet Session Status = INACTIVE
Network Information
===================
Current System Time = Mon Apr 18 6:22:7 2016
Current Service Status = Normal
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Network = Telstra
Mobile Country Code (MCC) = 505
Mobile Network Code (MNC) = 1
Packet switch domain(PS) state = Attached
Location Area Code (LAC) = 30802
Cell ID = 61079747
Radio Information
=================
Radio power mode = ON
Channel Number = 4412
Current Band = WCDMA 850
Current RSSI(RSCP) = -92 dBm
Current ECIO = -10 dBm
Radio Access Technology(RAT) Preference = AUTO
Radio Access Technology(RAT) Selected = UMTS ( HSDPA HSUPA UMTS/WCDMA WCDMA (Downlink) and HSUPA (Uplink) HSDPA (Downlink) and HSUPA (Uplink) )
Modem Security Information
==========================
Active SIM = 0
SIM switchover attempts = 0
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of CHV1 Retries remaining = 3
GPS Information
==========================
GPS Info
-------------
GPS Feature: enabled
GPS Port Selected: Dedicated GPS port
GPS State: GPS disabled
SMS Information
===============
Incoming Message Information
----------------------------
SMS stored in modem = 1
SMS archived since booting up = 0
Total SMS deleted since booting up = 0
Storage records allocated = 25
Storage records used = 1
Number of callbacks triggered by SMS = 0
Number of successful archive since booting up = 0
Number of failed archive since booting up = 0
Outgoing Message Information
----------------------------
Total SMS sent successfully = 0
Total SMS send failure = 0
Number of outgoing SMS pending = 0
Number of successful archive since booting up = 0
Number of failed archive since booting up = 0
Last Outgoing SMS Status = SUCCESS
Copy-to-SIM Status = 0x0
Send-to-Network Status = 0x0
Report-Outgoing-Message-Number:
Reference Number = 0
Result Code = 0x0
Diag Code = 0x0 0x0 0x0 0x0 0x0
SMS Archive URL =
Error Information
=================
This command is not supported on this platform.
Modem Crashdump Information
===========================
Modem crashdump logging: off
Router#show interface cellular 0
Cellular0 is up, line protocol is up
Hardware is 4G WWAN Modem - Global (Europe & Australia) Multimode LTE/DC-HSPA+/HSPA+/HSPA/U
Internet address is 10.106.18.202/32
MTU 1500 bytes, BW 384 Kbit/sec, DLY 100000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation SLIP, loopback not set
Keepalive not supported
Last input 00:02:41, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/10 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
55 packets input, 5432 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
61 packets output, 2893 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
Router#sh run
Building configuration...
Current configuration ytes
!
! Last configuration change at 06:32:30 UTC Mon Apr 18 2016
!
version 15.5
service timestamps debug datetime msec
service timestamps losec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
enable password cisco
!
no aaa new-model
ethernet lmi ce
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
ip dhcp excluded-address 1.1
!
ip dhcp pool LAN
network 10.1.1.0 255.255.255.0
default-router 10.1.1.1
dns-server 8.8.8.8
!
!
!
ip cef
no ipv6 cef
!
!
!
!
!
multilink bundle-name authenticated
!
!
chat-script lte "OUT 20 "OK"
!
!
!
!
!
license udi pid C899G-LTE-GA-K9 sn FCZ20069ABC
!
!
username admin privilege 15 password 0 cisco
!
!
!
!
!
controller Cellular 0
lte modem link-recovery rssi onset-threshold -110
lte modem link-recovery monitor-timer 20
lte modem link-recovery wait-timer 10
lte modem link-recovery debounce-count 6
!
!
!
!
!
!
!
!
!
!
!
!
interface Cellular0
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation slip
dialer in-band
dialer idle-timeout 0
dialer string lte
dialer-group 1
!
interface Cellular1
no ip address
encapsulation slip
!
interface FastEthernet0
no ip address
shutdown
duplex auto
speed auto
!
interface GigabitEthernet0
no ip address
!
interface GigabitEthernet1
no ip address
!
interface GigabitEthernet2
no ip address
!
interface GigabitEthernet3
no ip address
!
interface GigabitEthernet4
no ip address
!
interface GigabitEthernet5
no ip address
!
interface GigabitEthernet6
no ip address
!
interface GigabitEthernet7
no ip address
!
interface GigabitEthernet8
no ip address
shutdown
duplex auto
speed auto
!
interface GigabitEthernet9
no ip address
shutdown
duplex auto
speed auto
!
interface Vlan1
ip address 10.1.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
!
ip nat inside source list 1 interface Cellular0 overload
ip route 0.0.0.0 0.0.0.0 Cellular0
!
dialer-list 1 protocol ip permit
!
access-list 1 permit 10.1.1.0 0.0.0.255
!
control-plane
!
!
!
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
!
mgcp profile default
!
!
!
!
!
!
!
line con 0
password cisco
login
no modem enable
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
stopbits 1
line 3
script dialer lte
no exec
speed 384000
line 8
no exec
speed 384000
line vty 0 4
password cisco
login
transport input none
!
scheduler allocate 20000 1000
!
end
I've removed the Telstra SIM card on slot S0 in order to activate Optus SIM card on slot S1.
Router#debug chat
Router#debug dialer
*Apr 19 02:02:58.496: TTY0: resume timer type 1 (OK)
*Apr 19 02:02:58.504: TTY0: pause timer type 1 (OK)
*Apr 19 02:02:58.504: TTY0: resume timer type 1 (OK)
CALLCONTROL debugging is on
Router#
*Apr 19 02:03:01.584: TTY0: pause timer type 1 (OK)
*Apr 19 02:03:01.584: TTY0: resume timer type 1 (OK)
*Apr 19 02:03:16.416: api_manage_packet_session Removing IP DNS profile:0 active_prof:0
*Apr 19 02:03:16.416: TTY3: Async Int reset: Dropping DTR
*Apr 19 02:03:16.416: Cellular0 DirectIP: Remove negotiated IP interface address
*Apr 19 02:03:16.416: Cellular0 DirectIP: Primary DNS address 10.5.68.232 removed
*Apr 19 02:03:16.416: Cellular0 DirectIP: Secondary DNS address 10.5.80.241 removed
*Apr 19 02:03:18.044: cellwan_api_pkt_session_notify: instance id:0 profile:0 status:0
*Apr 19 02:03:18.044: %CELLWAN-2-BEARER_DELETED: Instance id=0, Default bearer (bearer_id=5) in Cellular0 is now deleted.
*Apr 19 02:03:18.044: Cellular0 profile 0, session INACTIVE
*Apr 19 02:03:18.044: Cellular0 DirectIP: Remove negotiated IP interface address
*Apr 19 02:03:18.416: %LINK-5-CHANGED: Interface Cellular0, changed state to reset
*Apr 19 02:03:19.416: %LINEPROTO-5-UPDOWN: Line protocol on Interface Cellular0, changed state to down
*Apr 19 02:03:21.416: TTY3: no timer type 0 to destroy
*Apr 19 02:03:21.416: TTY3: no timer type 1 to destroy
*Apr 19 02:03:21.416: TTY3: no timer type 3 to destroy
*Apr 19 02:03:21.416: TTY3: no timer type 4 to destroy
*Apr 19 02:03:21.416: TTY3: no timer type 10 to destroy
*Apr 19 02:03:21.416: TTY3: no timer type 2 to destroy
*Apr 19 02:03:21.416: TTY3: Async Int cleanup: Restoring DTR
*Apr 19 02:03:23.416: %LINK-3-UPDOWN: Interface Cellular0, changed state to down
Router#
*Apr 19 02:03:28.508: %CISCO800-2-MODEM_DOWN: Cellular0 modem is now DOWN.
*Apr 19 02:03:29.116: %CISCO800-6-SIM_ACTIVATION: SIM in slot 1 is being activated. Please
wait for modem to come UP.
Router#
*Apr 19 02:06:23.872: %CELLWAN-2-BEARER_UP: Instance id=0, Default bearer (bearer_id=5) in Cellular0 is now UP
*Apr 19 02:06:26.108: %LINK-3-UPDOWN: Interface Cellular0, changed state to up
*Apr 19 02:06:27.108: %LINEPROTO-5-UPDOWN: Line protocol on Interface Cellular0, changed state to up // TOOK AROUND 3 MINS FOR OPTUS SIM CARD TO BE ACTIVATED
I didn't configure any LTE profile for OPTUS since it took the default profile used for Telstra (Profile 1). This was the same scenario happened during my Singtel and M1 testing.
Router#show cellular 0 radio
Radio power mode = ON
LTE Rx Channel Number = 1725
LTE Tx Channel Number = 19725
LTE Band = 3
LTE Bandwidth = 15 MHz
Current RSSI = -85 dBm
Current RSRP = -117 dBm
Current RSRQ = -13 dB
Current SNR = 7.8 dB
Radio Access Technology(RAT) Preference = AUTO
Radio Access Technology(RAT) Selected = LTE
Router#show cellular 0 network
Current System Time = Tue Apr 19 2:7:30 2016
Current Service Status = Normal
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Network = OPTUS
Mobile Country Code (MCC) = 505
Mobile Network Code (MNC) = 2
Packet switch domain(PS) state = Attached
Registration state(EMM) = Registered
EMM Sub State = Normal Service
Tracking Area Code (TAC) = 59502
Cell ID = 27329034
Router#show cellular 0 profile
Profile 1 = ACTIVE* **
--------
PDP Type = IPv4
PDP address = 10.236.148.169 // OPTUS DHCP AND DNS IP
Access Point Name (APN) = telstra.internet
Authentication = None
Primary DNS address = 211.29.93.7
Secondary DNS address = 198.142.0.0
Profile 2 = INACTIVE
--------
PDP Type = IPv4
Access Point Name (APN) = yesinternet
Authentication = None
* - Default profile
** - LTE attach profile
Configured default profile for active SIM 1 is profile 1.
Router#show interface cellular 0
Cellular0 is up, line protocol is up
Hardware is 4G WWAN Modem - Global (Europe & Australia) Multimode LTE/DC-HSPA+/HSPA+/HSPA/U
Internet address is 10.236.148.169/32
MTU 1500 bytes, BW 50000 Kbit/sec, DLY 100000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation SLIP, loopback not set
Keepalive not supported
Last input 00:00:20, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 8
Queueing strategy: fifo
Output queue: 0/10 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
51989 packets input, 48280921 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
35863 packets output, 7060877 bytes, 0 underruns
0 output errors, 0 collisions, 3 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
Router#ping 8.8.8.8
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 104/145/304 ms
Router#traceroute 8.8.8.8
Type escape sequence to abort.
Tracing the route to google-public-dns-a.google.com (8.8.8.8)
VRF info: (vrf in name/id, vrf out name/id)
1 * * *
2 172.24.154.45 84 msec 36 msec 48 msec
3 * * *
4 * * *
5 10.194.125.2 92 msec 52 msec 52 msec
6 * * *
7 * * *
8 * * *
9 * * *
10 * * *
