I went to the Land of Smiles, Bangkok Thailand, the second time around and was hired to setup an office IT network that uses a Cisco 4331 router. I took a side trip after it was done and visited Wat Pho, which is one of the many Buddhist temples in Bangkok. This temple is known as the birthplace of the traditional Thai massage and it houses a huge reclining Buddha. Thai cuisine is amazingly good! I had Phat Thai (or Pad Thai), which is their famous stir-fried rice noodles, and Green Chicken Curry.
The Cisco 4331 is Cisco's latest ISR router in the 4000 series. The 4000 series routers are said to be 4-10 times faster (and cheaper) compared to the ISR G2 series routers. Here's the initial bootup process and startup-config. It now uses the IOS-XE which is Cisco classic IOS that runs on a Linux platform. There's also no need to issue a write erase and reload commands just to remove the default configurations such as the one-time username "cisco", ip http access-class 23 (used for HTTP/CCP) and transport input none (used on VTY lines), which locked me out of a router a few times.
Initializing Hardware ...
System integrity status: 00000610
Rom image verified correctly
System Bootstrap, Version 15.4(3r)S5, RELEASE SOFTWARE
Copyright (c) 1994-2015 by cisco Systems, Inc.
Current image running: Boot ROM0
Last reset cause: PowerOn
Cisco ISR4331/K9 platform with 4194304 Kbytes of main memory
no valid BOOT image found
Final autoboot attempt from default boot device...
Warning: filesystem is not clean
Warning: filesystem is not clean
File size is 0x1c0cd400
Located isr4300-universalk9.03.16.02.S.155-3.S2-ext.SPA.bin
Image size 470602752 inode num 12, bks cnt 114894 blk size 8*512
###############################################################################
Boot image size = 470602752 (0x1c0cd400) bytes
Package header rev 1 structure detected
Calculating SHA-1 hash...done
validate_package: SHA-1 hash:
calculated 964c232a:7ae904ce:2722d662:5a878b27:c84ad6da
expected 964c232a:7ae904ce:2722d662:5a878b27:c84ad6da
RSA Signed RELEASE Image Signature Verification Successful.
Package Load Test Latency : 8547 msec
Image validated
%IOSXEBOOT-4-FILESYS_ERRORS_CORRECTED: (rp/0): bootflash 1 contained errors which were auto-corrected.
%IOSXEBOOT-4-FILESYS_ERRORS_CORRECTED: (rp/0): bootflash 5 contained errors which were auto-corrected.
%IOSXEBOOT-4-FILESYS_ERRORS_CORRECTED: (rp/0): bootflash 6 contained errors which were auto-corrected.
%IOSXEBOOT-4-FILESYS_ERRORS_CORRECTED: (rp/0): bootflash 7 contained errors which were auto-corrected.
%IOSXEBOOT-4-FILESYS_ERRORS_CORRECTED: (rp/0): bootflash 8 contained errors which were auto-corrected.
%IOSXEBOOT-4-FILESYS_ERRORS_CORRECTED: (rp/0): bootflash 9 contained errors which were auto-corrected.
%IOSXEBOOT-4-FILESYS_ERRORS_CORRECTED: (rp/0): bootflash 10 contained errors which were auto-corrected.
%IOSXEBOOT-4-BOOT_SRC: (rp/0): mounting /boot/super.iso to /tmp/sw/isos
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.5(3)S2, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2016 by Cisco Systems, Inc.
Compiled Thu 11-Feb-16 08:58 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2016 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
% failed to initialize nvram
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco ISR4331/K9 (1RU) processor with 1655569K/6147K bytes of memory.
Processor board ID FDO2012A123
3 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
3223551K bytes of flash memory at bootflash:.
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]: no
Press RETURN to get started!
*Nov 29 05:16:16.090: %SMART_LIC-6-AGENT_READY: Smart Agent for Licensing is initialized
*Nov 29 05:16:17.867: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name = esg Next reboot level = ipbasek9 and License = ipbasek9
*Nov 29 05:16:19.041: %ISR_THROUGHPUT-6-LEVEL: Throughput level has been set to 100000 kbps
*Nov 29 05:16:20.019: %IOSXE_RP_NV-3-NV_ACCESS_FAIL: Initial read of NVRAM contents failed
*Nov 29 05:16:23.500: dev_pluggable_optics_selftest attribute table internally inconsistent @ 0x125
*Nov 29 05:16:27.288: %SPANTREE-5-EXTENDED_SYSID:
Router>Extended SysId enabled for type vlan
*Nov 29 05:16:28.261: %LINK-3-UPDOWN: Interface Lsmpi0, changed state to up
*Nov 29 05:16:28.262: %LINK-3-UPDOWN: Interface EOBC0, changed state to up
*Nov 29 05:16:28.262: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to down
*Nov 29 05:16:28.270: %LINK-3-UPDOWN: Interface LIIN0, changed state to up
*Nov 29 05:16:29.596: %IOSXE_MGMTVRF-6-CREATE_SUCCESS_INFO: Management vrf Mgmt-intf created with ID 1, ipv4 table-id 0x1, ipv6 table-id 0x1E000001
*Nov 29 05:16:29.647: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
*Nov 29 05:16:29.648: %LINEPROTO-5-UPDOWN: Line protocol on Interface Lsmpi0, changed state to up
*Nov 29 05:16:29.648: %LINEPROTO-5-UPDOWN: Line protocol on Interface EOBC0, changed state to up
*Nov 29 05:16:29.648: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Nov 29 05:16:29.648: %LINEPROTO-5-UPDOWN: Line protocol on Interface LIIN0, changed state to up
*Nov 29 05:16:21.218: %CMLIB-6-THROUGHPUT_VALUE: SIP1: cmand: Throughput license found, throughput set to 100000 kbps
*Nov 29 05:16:30.959: %IOSXE_OIR-6-REMSPA: SPA removed from subslot 0/0, interfaces disabled
*Nov 29 05:16:30.959: %IOSXE_OIR-6-REMSPA: SPA removed from subslot 0/1, interfaces disabled
*Nov 29 05:16:30.963: %SPA_OIR-6-OFFLINECARD: SPA (ISR4331-3x1GE) offline in subslot 0/0
*Nov 29 05:16:30.964: %SPA_OIR-6-OFFLINECARD: SPA (NIM-2FXS) offline in subslot 0/1
*Nov 29 05:16:30.968: %IOSXE_OIR-6-INSCARD: Card (fp) inserted in slot F0
*Nov 29 05:16:30.968: %IOSXE_OIR-6-ONLINECARD: Card (fp) online in slot F0
*Nov 29 05:16:30.969: %IOSXE_OIR-6-INSCARD: Card (cc) inserted in slot 0
*Nov 29 05:16:30.969: %IOSXE_OIR-6-ONLINECARD: Card (cc) online in slot 0
*Nov 29 05:16:30.973: %IOSXE_OIR-6-INSCARD: Card (cc) inserted in slot 1
*Nov 29 05:16:31.003: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 0/0
*Nov 29 05:16:31.007: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 0/1
*Nov 29 05:16:31.043: %SPA-3-ENVMON_NOT_MONITORED: SIP1: iomd: Environmental monitoring is not enabled for ISR4331-3x1GE[0/0]
*Nov 29 05:16:36.423: %SPA_OIR-6-ONLINECARD: SPA (ISR4331-3x1GE) online in subslot 0/0
*Nov 29 05:16:38.370: %LINK-3-UPDOWN: Interface GigabitEthernet0/0/0, changed state to down
*Nov 29 05:16:38.415: %LINK-3-UPDOWN: Interface GigabitEthernet0/0/1, changed state to down
*Nov 29 05:16:38.419: %LINK-3-UPDOWN: Interface GigabitEthernet0/0/2, changed state to down
*Nov 29 05:17:00.882: new extended attributes received from iomd(slot 0 bay 1 board 0)
*Nov 29 05:17:01.371: %SPA_OIR-6-ONLINECARD: SPA (NIM-2FXS) online in subslot 0/1
*Nov 29 05:17:01.372: %IOSXE_OIR-6-SOFT_RELOADSPA: SPA(NIM-2FXS) reloaded on subslot 0/1
*Nov 29 05:17:01.373: %SPA_OIR-6-OFFLINECARD: SPA (NIM-2FXS) offline in subslot 0/1
*Nov 29 05:17:35.853: %SPA_OIR-6-ONLINECARD: SPA (NIM-2FXS) online in subslot 0/1
*Nov 29 05:17:39.700: %LINK-3-UPDOWN: Interface Service-Engine0/1/0, changed state to up
*Nov 29 05:17:40.700: %LINEPROTO-5-UPDOWN: Line protocol on Interface Service-Engine0/1/0, changed state to up
*Nov 29 05:23:13.895: %LINK-5-CHANGED: Interface GigabitEthernet0/0/0, changed state to administratively down
*Nov 29 05:23:13.896: %LINK-5-CHANGED: Interface GigabitEthernet0/0/1, changed state to administratively down
*Nov 29 05:23:13.896: %LINK-5-CHANGED: Interface GigabitEthernet0/0/2, changed state to administratively down
*Nov 29 05:23:13.897: %LINK-5-CHANGED: Interface GigabitEthernet0, changed state to administratively down
*Nov 29 05:23:13.933: %LINK-5-CHANGED: Interface Vlan1, changed state to administratively down
*Nov 29 05:23:20.117: %SYS-5-RESTART: System restarted --
Cisco IOS Software, ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.5(3)S2, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2016 by Cisco Systems, Inc.
Compiled Thu 11-Feb-16 08:58 by mcpre
Router>enable
Router#
Router#show version
Cisco IOS XE Software, Version 03.16.02.S - Extended Support Release
Cisco IOS Software, ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.5(3)S2, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2016 by Cisco Systems, Inc.
Compiled Thu 11-Feb-16 08:58 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2016 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
Router uptime is 7 minutes
Uptime for this control processor is 8 minutes
System returned to ROM by reload at 03:53:06 UTC Thu Mar 24 2016
System image file is "bootflash:/isr4300-universalk9.03.16.02.S.155-3.S2-ext.SPA.bin"
Last reload reason: PowerOn
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Suite License Information for Module:'esg'
--------------------------------------------------------------------------------
Suite Suite Current Type Suite Next reboot
--------------------------------------------------------------------------------
FoundationSuiteK9 None None None
securityk9
appxk9
AdvUCSuiteK9 None None None
uck9
cme-srst
cube
Technology Package License Information:
-----------------------------------------------------------------
Technology Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------
appxk9 None None None
uck9 None None None
securityk9 None None None
ipbase ipbasek9 Permanent ipbasek9
cisco ISR4331/K9 (1RU) processor with 1655569K/6147K bytes of memory.
Processor board ID FDO2012A123
3 Gigabit Ethernet interfaces
2 Voice FXS interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
3223551K bytes of flash memory at bootflash:.
Configuration register is 0x2102
Router#show run
Building configuration...
Current configuration : 1293 bytes
!
! Last configuration change at 05:23:22 UTC Tue Nov 29 2016
!
version 15.5
service timestamps debug datetime msec
service timestamps log datetime msec
no platform punt-keepalive disable-kernel-core
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
vrf definition Mgmt-intf
!
address-family ipv4
exit-address-family
!
address-family ipv6
exit-address-family
!
!
no aaa new-model
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
subscriber templating
multilink bundle-name authenticated
!
!
!
!
license udi pid ISR4331/K9 sn FDO20090ABC
!
spanning-tree extend system-id
!
!
redundancy
mode none
!
!
vlan internal allocation policy ascending
!
!
!
!
!
!
interface GigabitEthernet0/0/0
no ip address
shutdown
negotiation auto
!
interface GigabitEthernet0/0/1
no ip address
shutdown
negotiation auto
!
interface GigabitEthernet0/0/2
no ip address
shutdown
negotiation auto
!
interface Service-Engine0/1/0
no ip address
!
interface GigabitEthernet0
vrf forwarding Mgmt-intf
no ip address
shutdown
negotiation auto
!
interface Vlan1
no ip address
shutdown
!
ip forward-protocol nd
no ip http server
no ip http secure-server
ip tftp source-interface GigabitEthernet0
!
!
!
!
!
!
control-plane
!
!
line con 0
stopbits 1
line aux 0
stopbits 1
line vty 0 4
login
!
!
end
These are the pictures of the front and back panels.
There's a dedicated out-of-band management port GE0 in front. It uses the default forwarding VRF Mgmt-intf, that can't be changed.
The serial number pull-out label is found at the back which is a bit long and foldable.
The Cisco 4000 uses a fourth generation Network Interface Module (NIM) cards, which is long and NOT supported on ISR G2 routers (such as 2900 and 3900). Below is a NIM-2FXS card that I've installed.
To install a PVDM4-64 module, you'll need to remove 6 small screws: 4 on top and 2 on the sides.
The Cisco 4331 router has only 1 PVDM slot which is found between the 3 heat sinks on the left of the picture.
Router#show inventory
NAME: "Chassis", DESCR: "Cisco ISR4331 Chassis"
PID: ISR4331/K9 , VID: V02, SN: FDO2012AABC
NAME: "Power Supply Module 0", DESCR: "250W AC Power Supply for Cisco ISR 4330"
PID: PWR-4330-AC , VID: V01, SN: DCA19501DEF
NAME: "Fan Tray", DESCR: "Cisco ISR4330 Fan Assembly"
PID: ACS-4330-FANASSY , VID: , SN:
NAME: "module 0", DESCR: "Cisco ISR4331 Built-In NIM controller"
PID: ISR4331/K9 , VID: , SN:
NAME: "NIM subslot 0/1", DESCR: "NIM-2FXS Voice Analog Module"
PID: NIM-2FXS , VID: V01, SN: FOC19494GHI
NAME: "PVDM subslot 0/4", DESCR: "PVDM4-64 Voice DSP Module"
PID: PVDM4-64 , VID: V02, SN: FOC20028JKL
NAME: "NIM subslot 0/0", DESCR: "Front Panel 3 ports Gigabitethernet Module"
PID: ISR4331-3x1GE , VID: V01, SN: JAB09270MNO
NAME: "module 1", DESCR: "Cisco ISR4331 Built-In SM controller"
PID: ISR4331/K9 , VID: , SN:
NAME: "module R0", DESCR: "Cisco ISR4331 Route Processor"
PID: ISR4331/K9 , VID: V02, SN: FDO20090PQR
NAME: "module F0", DESCR: "Cisco ISR4331 Forwarding Processor"
PID: ISR4331/K9 , VID: , SN:
The Cisco 4331 is Cisco's latest ISR router in the 4000 series. The 4000 series routers are said to be 4-10 times faster (and cheaper) compared to the ISR G2 series routers. Here's the initial bootup process and startup-config. It now uses the IOS-XE which is Cisco classic IOS that runs on a Linux platform. There's also no need to issue a write erase and reload commands just to remove the default configurations such as the one-time username "cisco", ip http access-class 23 (used for HTTP/CCP) and transport input none (used on VTY lines), which locked me out of a router a few times.
Initializing Hardware ...
System integrity status: 00000610
Rom image verified correctly
System Bootstrap, Version 15.4(3r)S5, RELEASE SOFTWARE
Copyright (c) 1994-2015 by cisco Systems, Inc.
Current image running: Boot ROM0
Last reset cause: PowerOn
Cisco ISR4331/K9 platform with 4194304 Kbytes of main memory
no valid BOOT image found
Final autoboot attempt from default boot device...
Warning: filesystem is not clean
Warning: filesystem is not clean
File size is 0x1c0cd400
Located isr4300-universalk9.03.16.02.S.155-3.S2-ext.SPA.bin
Image size 470602752 inode num 12, bks cnt 114894 blk size 8*512
###############################################################################
Boot image size = 470602752 (0x1c0cd400) bytes
Package header rev 1 structure detected
Calculating SHA-1 hash...done
validate_package: SHA-1 hash:
calculated 964c232a:7ae904ce:2722d662:5a878b27:c84ad6da
expected 964c232a:7ae904ce:2722d662:5a878b27:c84ad6da
RSA Signed RELEASE Image Signature Verification Successful.
Package Load Test Latency : 8547 msec
Image validated
%IOSXEBOOT-4-FILESYS_ERRORS_CORRECTED: (rp/0): bootflash 1 contained errors which were auto-corrected.
%IOSXEBOOT-4-FILESYS_ERRORS_CORRECTED: (rp/0): bootflash 5 contained errors which were auto-corrected.
%IOSXEBOOT-4-FILESYS_ERRORS_CORRECTED: (rp/0): bootflash 6 contained errors which were auto-corrected.
%IOSXEBOOT-4-FILESYS_ERRORS_CORRECTED: (rp/0): bootflash 7 contained errors which were auto-corrected.
%IOSXEBOOT-4-FILESYS_ERRORS_CORRECTED: (rp/0): bootflash 8 contained errors which were auto-corrected.
%IOSXEBOOT-4-FILESYS_ERRORS_CORRECTED: (rp/0): bootflash 9 contained errors which were auto-corrected.
%IOSXEBOOT-4-FILESYS_ERRORS_CORRECTED: (rp/0): bootflash 10 contained errors which were auto-corrected.
%IOSXEBOOT-4-BOOT_SRC: (rp/0): mounting /boot/super.iso to /tmp/sw/isos
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.5(3)S2, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2016 by Cisco Systems, Inc.
Compiled Thu 11-Feb-16 08:58 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2016 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
% failed to initialize nvram
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco ISR4331/K9 (1RU) processor with 1655569K/6147K bytes of memory.
Processor board ID FDO2012A123
3 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
3223551K bytes of flash memory at bootflash:.
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]: no
Press RETURN to get started!
*Nov 29 05:16:16.090: %SMART_LIC-6-AGENT_READY: Smart Agent for Licensing is initialized
*Nov 29 05:16:17.867: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name = esg Next reboot level = ipbasek9 and License = ipbasek9
*Nov 29 05:16:19.041: %ISR_THROUGHPUT-6-LEVEL: Throughput level has been set to 100000 kbps
*Nov 29 05:16:20.019: %IOSXE_RP_NV-3-NV_ACCESS_FAIL: Initial read of NVRAM contents failed
*Nov 29 05:16:23.500: dev_pluggable_optics_selftest attribute table internally inconsistent @ 0x125
*Nov 29 05:16:27.288: %SPANTREE-5-EXTENDED_SYSID:
Router>Extended SysId enabled for type vlan
*Nov 29 05:16:28.261: %LINK-3-UPDOWN: Interface Lsmpi0, changed state to up
*Nov 29 05:16:28.262: %LINK-3-UPDOWN: Interface EOBC0, changed state to up
*Nov 29 05:16:28.262: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to down
*Nov 29 05:16:28.270: %LINK-3-UPDOWN: Interface LIIN0, changed state to up
*Nov 29 05:16:29.596: %IOSXE_MGMTVRF-6-CREATE_SUCCESS_INFO: Management vrf Mgmt-intf created with ID 1, ipv4 table-id 0x1, ipv6 table-id 0x1E000001
*Nov 29 05:16:29.647: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
*Nov 29 05:16:29.648: %LINEPROTO-5-UPDOWN: Line protocol on Interface Lsmpi0, changed state to up
*Nov 29 05:16:29.648: %LINEPROTO-5-UPDOWN: Line protocol on Interface EOBC0, changed state to up
*Nov 29 05:16:29.648: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Nov 29 05:16:29.648: %LINEPROTO-5-UPDOWN: Line protocol on Interface LIIN0, changed state to up
*Nov 29 05:16:21.218: %CMLIB-6-THROUGHPUT_VALUE: SIP1: cmand: Throughput license found, throughput set to 100000 kbps
*Nov 29 05:16:30.959: %IOSXE_OIR-6-REMSPA: SPA removed from subslot 0/0, interfaces disabled
*Nov 29 05:16:30.959: %IOSXE_OIR-6-REMSPA: SPA removed from subslot 0/1, interfaces disabled
*Nov 29 05:16:30.963: %SPA_OIR-6-OFFLINECARD: SPA (ISR4331-3x1GE) offline in subslot 0/0
*Nov 29 05:16:30.964: %SPA_OIR-6-OFFLINECARD: SPA (NIM-2FXS) offline in subslot 0/1
*Nov 29 05:16:30.968: %IOSXE_OIR-6-INSCARD: Card (fp) inserted in slot F0
*Nov 29 05:16:30.968: %IOSXE_OIR-6-ONLINECARD: Card (fp) online in slot F0
*Nov 29 05:16:30.969: %IOSXE_OIR-6-INSCARD: Card (cc) inserted in slot 0
*Nov 29 05:16:30.969: %IOSXE_OIR-6-ONLINECARD: Card (cc) online in slot 0
*Nov 29 05:16:30.973: %IOSXE_OIR-6-INSCARD: Card (cc) inserted in slot 1
*Nov 29 05:16:31.003: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 0/0
*Nov 29 05:16:31.007: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 0/1
*Nov 29 05:16:31.043: %SPA-3-ENVMON_NOT_MONITORED: SIP1: iomd: Environmental monitoring is not enabled for ISR4331-3x1GE[0/0]
*Nov 29 05:16:36.423: %SPA_OIR-6-ONLINECARD: SPA (ISR4331-3x1GE) online in subslot 0/0
*Nov 29 05:16:38.370: %LINK-3-UPDOWN: Interface GigabitEthernet0/0/0, changed state to down
*Nov 29 05:16:38.415: %LINK-3-UPDOWN: Interface GigabitEthernet0/0/1, changed state to down
*Nov 29 05:16:38.419: %LINK-3-UPDOWN: Interface GigabitEthernet0/0/2, changed state to down
*Nov 29 05:17:00.882: new extended attributes received from iomd(slot 0 bay 1 board 0)
*Nov 29 05:17:01.371: %SPA_OIR-6-ONLINECARD: SPA (NIM-2FXS) online in subslot 0/1
*Nov 29 05:17:01.372: %IOSXE_OIR-6-SOFT_RELOADSPA: SPA(NIM-2FXS) reloaded on subslot 0/1
*Nov 29 05:17:01.373: %SPA_OIR-6-OFFLINECARD: SPA (NIM-2FXS) offline in subslot 0/1
*Nov 29 05:17:35.853: %SPA_OIR-6-ONLINECARD: SPA (NIM-2FXS) online in subslot 0/1
*Nov 29 05:17:39.700: %LINK-3-UPDOWN: Interface Service-Engine0/1/0, changed state to up
*Nov 29 05:17:40.700: %LINEPROTO-5-UPDOWN: Line protocol on Interface Service-Engine0/1/0, changed state to up
*Nov 29 05:23:13.895: %LINK-5-CHANGED: Interface GigabitEthernet0/0/0, changed state to administratively down
*Nov 29 05:23:13.896: %LINK-5-CHANGED: Interface GigabitEthernet0/0/1, changed state to administratively down
*Nov 29 05:23:13.896: %LINK-5-CHANGED: Interface GigabitEthernet0/0/2, changed state to administratively down
*Nov 29 05:23:13.897: %LINK-5-CHANGED: Interface GigabitEthernet0, changed state to administratively down
*Nov 29 05:23:13.933: %LINK-5-CHANGED: Interface Vlan1, changed state to administratively down
*Nov 29 05:23:20.117: %SYS-5-RESTART: System restarted --
Cisco IOS Software, ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.5(3)S2, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2016 by Cisco Systems, Inc.
Compiled Thu 11-Feb-16 08:58 by mcpre
Router>enable
Router#
Router#show version
Cisco IOS XE Software, Version 03.16.02.S - Extended Support Release
Cisco IOS Software, ISR Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.5(3)S2, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2016 by Cisco Systems, Inc.
Compiled Thu 11-Feb-16 08:58 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2016 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
Router uptime is 7 minutes
Uptime for this control processor is 8 minutes
System returned to ROM by reload at 03:53:06 UTC Thu Mar 24 2016
System image file is "bootflash:/isr4300-universalk9.03.16.02.S.155-3.S2-ext.SPA.bin"
Last reload reason: PowerOn
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Suite License Information for Module:'esg'
--------------------------------------------------------------------------------
Suite Suite Current Type Suite Next reboot
--------------------------------------------------------------------------------
FoundationSuiteK9 None None None
securityk9
appxk9
AdvUCSuiteK9 None None None
uck9
cme-srst
cube
Technology Package License Information:
-----------------------------------------------------------------
Technology Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------
appxk9 None None None
uck9 None None None
securityk9 None None None
ipbase ipbasek9 Permanent ipbasek9
cisco ISR4331/K9 (1RU) processor with 1655569K/6147K bytes of memory.
Processor board ID FDO2012A123
3 Gigabit Ethernet interfaces
2 Voice FXS interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
3223551K bytes of flash memory at bootflash:.
Configuration register is 0x2102
Router#show run
Building configuration...
Current configuration : 1293 bytes
!
! Last configuration change at 05:23:22 UTC Tue Nov 29 2016
!
version 15.5
service timestamps debug datetime msec
service timestamps log datetime msec
no platform punt-keepalive disable-kernel-core
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
vrf definition Mgmt-intf
!
address-family ipv4
exit-address-family
!
address-family ipv6
exit-address-family
!
!
no aaa new-model
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
subscriber templating
multilink bundle-name authenticated
!
!
!
!
license udi pid ISR4331/K9 sn FDO20090ABC
!
spanning-tree extend system-id
!
!
redundancy
mode none
!
!
vlan internal allocation policy ascending
!
!
!
!
!
!
interface GigabitEthernet0/0/0
no ip address
shutdown
negotiation auto
!
interface GigabitEthernet0/0/1
no ip address
shutdown
negotiation auto
!
interface GigabitEthernet0/0/2
no ip address
shutdown
negotiation auto
!
interface Service-Engine0/1/0
no ip address
!
interface GigabitEthernet0
vrf forwarding Mgmt-intf
no ip address
shutdown
negotiation auto
!
interface Vlan1
no ip address
shutdown
!
ip forward-protocol nd
no ip http server
no ip http secure-server
ip tftp source-interface GigabitEthernet0
!
!
!
!
!
!
control-plane
!
!
line con 0
stopbits 1
line aux 0
stopbits 1
line vty 0 4
login
!
!
end
These are the pictures of the front and back panels.
There's a dedicated out-of-band management port GE0 in front. It uses the default forwarding VRF Mgmt-intf, that can't be changed.
The serial number pull-out label is found at the back which is a bit long and foldable.
The Cisco 4000 uses a fourth generation Network Interface Module (NIM) cards, which is long and NOT supported on ISR G2 routers (such as 2900 and 3900). Below is a NIM-2FXS card that I've installed.
To install a PVDM4-64 module, you'll need to remove 6 small screws: 4 on top and 2 on the sides.
The Cisco 4331 router has only 1 PVDM slot which is found between the 3 heat sinks on the left of the picture.
Router#show inventory
NAME: "Chassis", DESCR: "Cisco ISR4331 Chassis"
PID: ISR4331/K9 , VID: V02, SN: FDO2012AABC
NAME: "Power Supply Module 0", DESCR: "250W AC Power Supply for Cisco ISR 4330"
PID: PWR-4330-AC , VID: V01, SN: DCA19501DEF
NAME: "Fan Tray", DESCR: "Cisco ISR4330 Fan Assembly"
PID: ACS-4330-FANASSY , VID: , SN:
NAME: "module 0", DESCR: "Cisco ISR4331 Built-In NIM controller"
PID: ISR4331/K9 , VID: , SN:
NAME: "NIM subslot 0/1", DESCR: "NIM-2FXS Voice Analog Module"
PID: NIM-2FXS , VID: V01, SN: FOC19494GHI
NAME: "PVDM subslot 0/4", DESCR: "PVDM4-64 Voice DSP Module"
PID: PVDM4-64 , VID: V02, SN: FOC20028JKL
NAME: "NIM subslot 0/0", DESCR: "Front Panel 3 ports Gigabitethernet Module"
PID: ISR4331-3x1GE , VID: V01, SN: JAB09270MNO
NAME: "module 1", DESCR: "Cisco ISR4331 Built-In SM controller"
PID: ISR4331/K9 , VID: , SN:
NAME: "module R0", DESCR: "Cisco ISR4331 Route Processor"
PID: ISR4331/K9 , VID: V02, SN: FDO20090PQR
NAME: "module F0", DESCR: "Cisco ISR4331 Forwarding Processor"
PID: ISR4331/K9 , VID: , SN:
No comments:
Post a Comment