I almost woke up my baby girl who was sleeping that night when I booted up the 2811 router for the first time. It made a loud noise fan upon boot up but went silent afterwards.
Router#show version
Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(16), RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 20-Jun-07 07:19 by prod_rel_team
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
Router uptime is 6 minutes
System returned to ROM by power-on
System image file is "flash:c2800nm-advipservicesk9-mz.124-16.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/techsupport
If you require further assistance please contact us by sending email to
export@cisco.com.
Cisco 2811 (revision 53.51) with 249856K/12288K bytes of memory.
Processor board ID FHK1129F477
2 FastEthernet interfaces
2 Serial(sync/async) interfaces
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
62720K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
Router#show environment all
Main Power Supply is AC
Fan 1 OK
Fan 2 OK
Fan 3 OK
System Temperature: 24 Celsius (normal)
Environmental information last updated 00:00:03 ago
I also tested my NM-8A/S network module and upgraded the IOS on my 2811. My Frame Relay switch is now ready. All I need now are my serial cables. The 2811 will also make a perfect Call Manager Express (CME) router if I choose to take the Cisco voice track.
Router#show inventory
NAME: "2811 chassis", DESCR: "2811 chassis"
PID: CISCO2811 , VID: V05 , SN: FHK1129F40H
NAME: "Eight Port Low-Speed A/S Serial", DESCR: "Eight Port Low-Speed A/S Serial"
PID: NM-8A/S= , VID: 1.0, SN: 28816743
Router#show ip interface brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 unassigned YES unset administratively down down
FastEthernet0/1 unassigned YES unset administratively down down
Serial1/0 unassigned YES unset administratively down down
Serial1/1 unassigned YES unset administratively down down
Serial1/2 unassigned YES unset administratively down down
Serial1/3 unassigned YES unset administratively down down
Serial1/4 unassigned YES unset administratively down down
Serial1/5 unassigned YES unset administratively down down
Serial1/6 unassigned YES unset administratively down down
Serial1/7 unassigned YES unset administratively down down
Router#show diag
Slot 0:
C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time unknown
Onboard VPN : v2.2.0
EEPROM contents at hardware discovery:
PCB Serial Number : FOC11276FF2
Hardware Revision : 1.0
Top Assy. Part Number : 800-26920-04
Board Revision : A0
Deviation Number : 0
Fab Version : 04
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 87
Hardware date code : 20070710
Chassis Serial Number : FHK1129F40H
Chassis MAC Address : 001c.58b9.3d58
MAC Address block size : 24
CLEI Code : COM7R00ARA
Product (FRU) Number : CISCO2811
Part Number : 73-10258-05
Version Identifier : V05
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF C1 8B 46 4F 43 31 31 32 37 36 46 46 32 40
0x10: 03 E7 41 01 00 C0 46 03 20 00 69 28 04 42 41 30
0x20: 88 00 00 00 00 02 04 03 00 81 00 00 00 00 04 00
0x30: 09 87 83 01 32 41 36 C2 8B 46 48 4B 31 31 32 39
0x40: 46 34 30 48 C3 06 00 1C 58 B9 3D 58 43 00 18 C6
0x50: 8A 43 4F 4D 37 52 30 30 41 52 41 CB 8F 43 49 53
0x60: 43 4F 32 38 31 31 20 20 20 20 20 20 82 49 28 12
0x70: 05 89 56 30 35 20 D9 02 40 C1 FF FF FF FF FF FF
Slot 1:
Sync/Async Port adapter, 8 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware revision 1.0 Board revision E0
Serial number 28816743 Part number 800-01225-03
FRU Part Number NM-8A/S=
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x00: 01 25 01 00 01
01 25 01 00 01 B7 B5 67 50 04 C9 03 00 00 00 000x10: 70 00 00 00 02 08 02 17 FF FF FF FF FF FF FF FF
0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x30: FF FF FF FF FF FF FF FF FF FF FF FF
Router#copy tftp://192.168.1.2/c2800nm-adventerprisek9-mz.124-24.T8.bin flash
Destination filename [c2800nm-adventerprisek9-mz.124-24.T8.bin]?
Accessing tftp://192.168.1.2/c2800nm-adventerprisek9-mz.124-24.T8.bin...
Erase flash: before copying? [confirm]
Erasing the flash filesystem will remove all files! Continue? [confirm]
Erasing device... eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee ...erased
Erase of flash: complete
Loading c2800nm-adventerprisek9-mz.124-24.T8.bin from 192.168.1.2 (via FastEthernet0/0): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
[OK - 59490092 bytes]
Verifying checksum... CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC OK (0xEFB5)
59490092 bytes copied in 779.836 secs (76285 bytes/sec)
Router#show flash
CompactFlash directory:
File Length Name/status
1 59490092 c2800nm-adventerprisek9-mz.124-24.T8.bin
[59490156 bytes used, 4735120 available, 64225276 total]
62720K bytes of ATA CompactFlash (Read/Write)
Router#reload
System configuration has been modified. Save? [yes/no]: y
Building configuration...
[OK]
Proceed with reload? [confirm]
*Jan 31 00:16:35.791: %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload Command.
System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2006 by cisco Systems, Inc.
Initializing memory for ECC
.
c2811 platform with 262144 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled
Readonly ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0x38bbd64
Self decompressing the image : ################################################################################################################################################################################################################################################################################################################################################### [OK]
Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
0003E7 0X00474800 C2811 Mainboard
000025 0X00033480 Eight port Async/Sync
0X00264050 Onboard VPN
0X000021B8 Onboard USB
0X002C29F0 public buffer pools
0X00211000 public particle pools
TOTAL: 0X00BE1878
If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.
Rounded IOMEM up to: 12Mb.
Using 4 percent iomem. [12Mb/256Mb]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013
252.227-7013.cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(24)T8, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Sun 09-Sep-12 04:01 by prod_rel_team
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/techsupport
If you require further assistance please contact us by sending email to
export@cisco.com.
Installed image archive
Cisco 2811 (revision 49.46) with 249856K/12288K bytes of memory.
Processor board ID FHK1129F40H
2 FastEthernet interfaces
8 Low-speed serial(sync/async) interfaces
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
62720K bytes of ATA CompactFlash (Read/Write)
Press RETURN to get started!
*Jan 31 00:20:31.731: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed to: Initialized
*Jan 31 00:20:31.739: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed to: Enabled
*Jan 31 00:20:33.851: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to up
*Jan 31 00:20:33.851: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Jan 31 00:20:33.851: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
*Jan 31 00:20:33.855: %LINK-3-UPDOWN: Interface Serial1/0, changed state to down
*Jan 31 00:20:33.855: %LINK-3-UPDOWN: Interface Serial1/1, changed state to down
*Jan 31 00:20:33.855: %LINK-3-UPDOWN: Interface Serial1/2, changed state to down
*Jan 31 00:20:33.855: %LINK-3-UPDOWN: Interface Serial1/3, changed state to down
*Jan 31 00:20:33.855: %LINK-3-UPDOWN: Interface Serial1/4, changed state to down
*Jan 31 00:20:33.855: %LINK-3-UPDOWN: Interface Serial1/5, changed state to down
*Jan 31 00:20:33.855: %LINK-3-UPDO
Router>WN: Interface Serial1/6, changed state to down
*Jan 31 00:20:33.855: %LINK-3-UPDOWN: Interface Serial1/7, changed state to down
*Jan 31 00:20:35.275: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
*Jan 31 00:20:35.275: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down
*Jan 31 00:20:35.275: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to down
*Jan 31 00:20:35.275: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/1, changed state to down
*Jan 31 00:20:35.275: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/2, changed state to down
*Jan 31 00:20:35.275: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/3, changed state to down
*Jan 31 00:20:35.275: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/4, changed state to down
*Jan 31 00:20:35.275: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/5, changed state to down
*Jan 31 00:20:35.275: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/6, changed state to down
*Jan 31 00:20:35.275: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/7, changed state to down
*Jan 31 00:20:37.635: %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to administratively down
*Jan 31 00:20:37.679: %LINK-5-CHANGED: Interface Serial1/0, changed state to administratively down
*Jan 31 00:20:37.695: %LINK-5-CHANGED: Interface Serial1/1, changed state to administratively down
*Jan 31 00:20:37.703: %LINK-5-CHANGED: Interface Serial1/2, changed state to administratively down
*Jan 31 00:20:37.711: %LINK-5-CHANGED: Interface Serial1/3, changed state to administratively down
*Jan 31 00:20:37.723: %LINK-5-CHANGED: Interface Serial1/4, changed state to administratively down
*Jan 31 00:20:37.731: %LINK-5-CHANGED: Interface Serial1/5, changed state to administratively down
*Jan 31 00:20:37.739: %LINK-5-CHANGED: Interface Serial1/6, changed state to administratively down
*Jan 31 00:20:37.751: %LINK-5-CHANGED: Interface Serial1/7, changed state to administratively down
*Jan 31 00:20:39.439: %SYS-5-RESTART: System restarted --
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(24)T8, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Sun 09-Sep-12 04:01 by prod_rel_team
*Jan 31 00:20:39.451: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
*Jan 31 00:20:39.711: %SYS-6-BOOTTIME: Time taken to reboot after reload = 243 seconds
*Jan 31 00:20:39.895: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Jan 31 00:20:39.895: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF
*Jan 31 00:20:39.899: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Jan 31 00:20:39.899: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF
Router>enable
Router#show version
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(24)T8, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Sun 09-Sep-12 04:01 by prod_rel_team
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
Router uptime is 1 minute
System returned to ROM by reload at 00:16:35 UTC Fri Jan 31 2014
System image file is "flash:c2800nm-adventerprisek9-mz.124-24.T8.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/techsupport
If you require further assistance please contact us by sending email to
export@cisco.com.
Cisco 2811 (revision 53.50) with 249856K/12288K bytes of memory.
Processor board ID FHK1129F40H
2 FastEthernet interfaces
8 Low-speed serial(sync/async) interfaces
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
62720K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
No comments:
Post a Comment