I was asked to configure a Cisco 899G 4G LTE router. This is to quickly deploy Internet access for remote sites using 4G/LTE as its medium for WAN connectivity. 4G uses a nano SIM card and you'll need a 2G SIM card adapter in order to fit into the router's SIM card slot. Below is what a nano SIM card adapter looks like.
This is the front panel of the Cisco 899G LTE router.
These are the ports at the back of the router. It has dual 4G antennas, a built-in 8-port GigabitEthernet switch (GE ports 0-7), dual GigabitEthernet WAN ports (GE WAN ports 8 and 9) with the option for fiber SFP for one GE WAN. The dual SIM card slot is covered by a metal plate and you'll need a flathead screwdriver to press it down and pull it off.
Once the metal cover is removed, take note of the orientation for inserting the SIM card using the SIM icon/drawing beside S0 and S1.
There is also an option to use an extended antenna (4G-AE010-R) to get a better signal.
Once the router completely boots up, take note of the LED lights in front such as the SIM card slot number, the signal strength (RSSI) and if LTE/WWAN is active.
Below is the initial router bootup.
System Bootstrap, Version 15.4(3r)M1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2014 by cisco Systems, Inc.
bad checksum, p_nvram 0x415d70
Correcting the backup nv_flash
Total memory size = 1024 MB
C899G-LTE-GA-K9 platform with 1048576 Kbytes of main memory
Main memory is configured to 32 bit mode
Readonly ROMMON initialized
IOS Image Load Test
___________________
Digitally Signed Production Software
Self decompressing the image :
##################################################################################################
##################################################################################################
##################################################################################################
##################################################################################################
##################################################################################################
##################################################################################################
##################################################################################################
######################################################################################## [OK]
*** No sreloc section
Smart Init is enabled
smart init is sizing iomem
TYPE MEMORY_REQ
Onboard devices &
buffer pools 0x03AECEC0
-----------------------------------------------
TOTAL: 0x03AECEC0
Rounded IOMEM up to: 58Mb.
Using 6 percent iomem. [58Mb/896Mb]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C800 Software (C800-UNIVERSALK9-M), Version 15.5(3)M, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Wed 22-Jul-15 23:59 by prod_rel_team
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Cisco C899G-LTE-GA-K9 (revision 1.0) with 857164K/60339K bytes of memory.Installed image archive
Processor board ID FCZ20069123
1 FastEthernet interface
10 Gigabit Ethernet interfaces
3 terminal lines
1 Virtual Private Network (VPN) Module
2 Cellular interfaces
DRAM configuration is 32 bits wide
255K bytes of non-volatile configuration memory.
1000944K bytes of ATA System CompactFlash (Read/Write)
%Error opening tftp://255.255.255.255/network-confg (Socket error)
%Error opening tftp://255.255.255.255/cisconet.cfg (Socket error)
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]: no
Press RETURN to get started!
*Jan 2 00:00:01.031: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name = c800 Next reboot level = advipservices and License = advipservices
*Apr 1 14:25:17.839: c3600_scp_set_dstaddr2_idb(184)add = 80 name is Embedded-Service-Engine0
*Apr 1 14:25:18.127: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed to: Initialized
*Apr 1 14:25:18.127: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed to: Enabled
*Apr 1 14:25:34.311: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to up
*Apr 1 14: %LINK-3-UPDOWN: Interface GigabitEthernet8, changed state to up
*Apr 1 14:25:34.311: %LINK-3-UPDOWN: Interface GigabitEthernet9, changed state to up
*Apr 1 14:25:34.311: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Apr 1 14:25:35.011: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
*Apr 1 14:25:35.311: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet8, changed state to down
*Apr 1 14:25:35.311: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet9, changed state to down
*Apr 1 14:25:35.311: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Apr 1 14:25:37.011: %LINK-3-UPDOWN: Interface GigabitEthernet9, changed state to down
*Apr 1 14:25:37.011: %LINK-3-UPDOWN: Interface GigabitEthernet8, changed state to down
*Apr 1 14:26:19.091: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse from
(tftp://255.255.255.255/network-confg) failed
*Apr 1 14:26:19.167: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse from
(tftp://255.255.255.255/cisconet.cfg) failed
*Apr 1 14:26:28.379: %LINK-5-CHANGED: Interface FastEthernet0, changed state to administratively down
*Apr 1 14:26:28.955: %LINK-5-CHANGED: Interface GigabitEthernet8, changed state to
administratively down
*Apr 1 14:26:28.983: %LINK-5-CHANGED: Interface GigabitEthernet9, changed state to
administratively down
*Apr 1 14:26:29.379: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
*Apr 1 14:26:33.667: %LINK-3-UPDOWN: Interface Ethernet10, changed state to up
*Apr 1 14:26:34.815: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet10, changed state to up
*Apr 1 14:26:36.399: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Apr 1 14:26:36.399: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1, changed state to down
*Apr 1 14:26:36.619: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2, changed state to down
*Apr 1 14:26:36.619: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet3, changed state to down
*Apr 1 14:26:36.619: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet4, changed state to down
*Apr 1 14:26:36.619: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet5, changed state to down
*Apr 1 14:26:36.619: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet6, changed state to down
*Apr 1 14:26:36.619: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet7, changed state to down
*Apr 1 14:26:38.039: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C800 Software (C800-UNIVERSALK9-M), Version 15.5(3)M, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Wed 22-Jul-15 23:59 by prod_rel_team
*Apr 1 14:26:38.255: ifs_open failed, path flash:1:/env_vars errno 2574
*Apr 1 14:26:38.347: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Apr 1 14:26:38.347: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF
*Apr 1 14:26:43.575: %SECONDCORE-5-BOOTSTAGE: ROMMON on 2nd core UP
*Apr 1 14:26:43.587: %SECONDCORE-5-BOOTSTAGE: BOOTLOADER on 2nd core UP
*Apr 1 14:26:47.719: %SECONDCORE-5-BOOTSTAGE: LINUX on 2nd core UP
Router>show ip interface brief
Interface IP-Address OK? Method Status Protocol
Cellular0 unassigned YES unset down down
Cellular1 unassigned YES unset down down
FastEthernet0 unassigned YES unset administratively down down
GigabitEthernet0 unassigned YES unset down down
GigabitEthernet1 unassigned YES unset down down
GigabitEthernet2 unassigned YES unset down down
GigabitEthernet3 unassigned YES unset down down
GigabitEthernet4 unassigned YES unset down down
GigabitEthernet5 unassigned YES unset down down
GigabitEthernet6 unassigned YES unset down down
GigabitEthernet7 unassigned YES unset down down
GigabitEthernet8 unassigned YES unset administratively down down
GigabitEthernet9 unassigned YES unset administratively down down
Vlan1 unassigned YES unset down down
Router>
Router>show version
Cisco IOS Software, C800 Software (C800-UNIVERSALK9-M), Version 15.5(3)M, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Wed 22-Jul-15 23:59 by prod_rel_team
ROM: System Bootstrap, Version 15.4(3r)M1, RELEASE SOFTWARE (fc1)
Router uptime is 2 minutes
System returned to ROM by power-on
System image file is "flash:c800-universalk9-mz.SPA.155-3.M.bin"
Last reload type: Normal Reload
Last reload reason: power-on
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Cisco C899G-LTE-GA-K9 (revision 1.0) with 857164K/60339K bytes of memory.
Processor board ID FCZ20069123
1 FastEthernet interface
10 Gigabit Ethernet interfaces
3 terminal lines
1 Virtual Private Network (VPN) Module
2 Cellular interfaces
DRAM configuration is 32 bits wide
255K bytes of non-volatile configuration memory.
1000944K bytes of ATA System CompactFlash (Read/Write)
License Info:
License UDI:
-------------------------------------------------
Device# PID SN
-------------------------------------------------
*1 C899G-LTE-GA-K9 FCZ20069123
License Information for 'c800'
License Level: advipservices Type: Permanent
Next reboot license Level: advipservices
Configuration register is 0x2102
Router>
*Apr 1 14:27:34.823: %CISCO800-2-MODEM_UP: Cellular0 modem is now UP
Router#show ip interface brief
Interface IP-Address OK? Method Status Protocol
Cellular0 unassigned YES unset up up
Cellular1 unassigned YES unset down down
FastEthernet0 unassigned YES unset administratively down down
GigabitEthernet0 unassigned YES unset down down
GigabitEthernet1 unassigned YES unset down down
GigabitEthernet2 unassigned YES unset down down
GigabitEthernet3 unassigned YES unset down down
GigabitEthernet4 unassigned YES unset down down
GigabitEthernet5 unassigned YES unset down down
GigabitEthernet6 unassigned YES unset down down
GigabitEthernet7 unassigned YES unset down down
GigabitEthernet8 unassigned YES unset administratively down down
GigabitEthernet9 unassigned YES unset administratively down down
Vlan1 unassigned YES unset down down
Router>enable
Router#show cell ?
<0-1> Cellular interface number
Router#show cell 0 ?
all Display all the information
connection Current active connection and statistics
gps Cellular gps information
hardware Cellular modem hardware information
logs Modem logging information
microcode Cellular microcode information
network Cellular network information
oma-dm LTE OMA DM information
profile Profile information in the modem
qos Current QoS configuration and statistics
radio Cellular modem radio information
security Modem security status
sms SMS information
Router#show cell 0 radio
Radio power mode = ON
LTE Rx Channel Number = 3250
LTE Tx Channel Number = 19300
LTE Band = 7
LTE Bandwidth = 20 MHz
Current RSSI = -63 dBm // STRONG SIGNAL
Current RSRP = -91 dBm
Current RSRQ = -9 dB
Current SNR = 6.8 dB
Radio Access Technology(RAT) Preference = AUTO
Radio Access Technology(RAT) Selected = LTE
Below is a useful RSSI reference chart.
Router#show cell 0 network
Current System Time = Fri Apr 1 14:32:36 2016
Current Service Status = Normal
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Network = SingTel
Mobile Country Code (MCC) = 525
Mobile Network Code (MNC) = 1
Packet switch domain(PS) state = Attached
Registration state(EMM) = Registered
EMM Sub State = Normal Service
Tracking Area Code (TAC) = 710
Cell ID = 188590849
Router#show cell 0 profile
Profile 1 = INACTIVE* **
--------
PDP Type = IPv4v6
Access Point Name (APN) =
Authentication = None
* - Default profile
** - LTE attach profile
Configured default profile for active SIM 0 is profile 1.
Router#show cell 0 security
Active SIM = 0 // WILL DISPLAY A "1" IF 4G SIM CARD IS INSERTED IN SIM1 SLOT
SIM switchover attempts = 0
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of CHV1 Retries remaining = 3
Router#show cell 0 all
Hardware Information
====================
Modem Firmware Version = SWI9X15C_05.05.58.00
Modem Firmware built = 2015/03/04 21:30:23
Hardware Version = 1.0
Device Model ID: MC7304
Package Identifier ID: 1102029_9903299_MC7304_05.05.58.00_00_Cisco_005.010_000
International Mobile Subscriber Identity (IMSI) = 525016118316xxx
International Mobile Equipment Identity (IMEI) = 352761060732xxx
Integrated Circuit Card ID (ICCID) = 8965011301141677xxx
Mobile Subscriber Integrated Services
Digital Network-Number (MSISDN) = 6591133xxx
Current Modem Temperature = 35 deg C
PRI SKU ID = 9903299, PRI version = 05.10, Carrier = 1
Profile Information
====================
Profile 1 = INACTIVE* **
--------
PDP Type = IPv4v6
Access Point Name (APN) =
Authentication = None
* - Default profile
** - LTE attach profile
Configured default profile for active SIM 0 is profile 1.
Data Connection Information
===========================
Profile 1, Packet Session Status = INACTIVE
Profile 2, Packet Session Status = INACTIVE
Profile 3, Packet Session Status = INACTIVE
Profile 4, Packet Session Status = INACTIVE
Profile 5, Packet Session Status = INACTIVE
Profile 6, Packet Session Status = INACTIVE
Profile 7, Packet Session Status = INACTIVE
Profile 8, Packet Session Status = INACTIVE
Profile 9, Packet Session Status = INACTIVE
Profile 10, Packet Session Status = INACTIVE
Profile 11, Packet Session Status = INACTIVE
Profile 12, Packet Session Status = INACTIVE
Profile 13, Packet Session Status = INACTIVE
Profile 14, Packet Session Status = INACTIVE
Profile 15, Packet Session Status = INACTIVE
Profile 16, Packet Session Status = INACTIVE
Network Information
===================
Current System Time = Fri Apr 1 14:36:37 2016
Current Service Status = Normal
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Network = SingTel
Mobile Country Code (MCC) = 525
Mobile Network Code (MNC) = 1
Packet switch domain(PS) state = Attached
Registration state(EMM) = Registered
EMM Sub State = Normal Service
Tracking Area Code (TAC) = 710
Cell ID = 188590849
Radio Information
=================
Radio power mode = ON
LTE Rx Channel Number = 3250
LTE Tx Channel Number = 19300
LTE Band = 7
LTE Bandwidth = 20 MHz
Current RSSI = -63 dBm
Current RSRP = -91 dBm
Current RSRQ = -9 dB
Current SNR = 4.4 dB
Radio Access Technology(RAT) Preference = AUTO
Radio Access Technology(RAT) Selected = LTE
Modem Security Information
==========================
Active SIM = 0
SIM switchover attempts = 0
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of CHV1 Retries remaining = 3
GPS Information
==========================
GPS Info
-------------
GPS Feature: enabled
GPS Port Selected: Dedicated GPS port
GPS State: GPS disabled
SMS Information
===============
Incoming Message Information
----------------------------
SMS stored in modem = 0
SMS archived since booting up = 0
Total SMS deleted since booting up = 0
Storage records allocated = 25
Storage records used = 0
Number of callbacks triggered by SMS = 0
Number of successful archive since booting up = 0
Number of failed archive since booting up = 0
Outgoing Message Information
----------------------------
Total SMS sent successfully = 0
Total SMS send failure = 0
Number of outgoing SMS pending = 0
Number of successful archive since booting up = 0
Number of failed archive since booting up = 0
Last Outgoing SMS Status = SUCCESS
Copy-to-SIM Status = 0x0
Send-to-Network Status = 0x0
Report-Outgoing-Message-Number:
Reference Number = 0
Result Code = 0x0
Diag Code = 0x0 0x0 0x0 0x0 0x0
SMS Archive URL =
Error Information
=================
This command is not supported on this platform.
Modem Crashdump Information
===========================
Modem crashdump logging: off
Router#show interface cell0
Cellular0 is up (spoofing), line protocol is up (spoofing)
Hardware is 4G WWAN Modem - Global (Europe & Australia) Multimode LTE/DC-HSPA+/HSPA+/HSPA/U
Internet address will be assigned dynamically by the network
MTU 1500 bytes, BW 9 Kbit/sec, DLY 100000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation SLIP, loopback not set
Keepalive not supported
Last input 00:02:35, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/10 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
9 packets input, 828 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
8 packets output, 800 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
I've used the SingTel Acces Point Name (APN) settings below for the LTE profile configuration (also works with a SingTel 3G SIM card). This link provides the APN info for Singapore mobile carriers while this link provides the APN for mobile carriers in different countries.
Router#cell ?
<0-1> Cellular interface number
Router#cell 0 ?
lte LTE Technology Commands
Router#cell 0 lte ?
oma-dm Open Mobile Alliance Device Management
plmn PLMN Commands
prl-region View/set PRL region
profile LTE Profile management commands
sim SIM card commands
sms SMS Commands
technology LTE Technology Preferences
Router#cell 0 lte profile ?
create Create/Edit a Profile
delete Delete a profile
Router#cell 0 lte profile create ?
<1-16> Profile Number
Router#cell 0 lte profile create 1 ?
WORD Access Point Name
<cr>
Router#cell 0 lte profile create 1 e-ideas ?
chap CHAP authentication only
none No authentication
pap PAP authentication only
pap_chap PAP or CHAP authentication
<cr>
Router#cell 0 lte profile create 1 e-ideas chap ?
WORD Username
Router#cell 0 lte profile create 1 e-ideas chap 65ideas ?
WORD Password
<cr>
Router#cell 0 lte profile create 1 e-ideas chap 65ideas 65ideas ?
ipv4 IPv4 type Bearer
ipv4v6 IPV4V6 type Bearer
ipv6 IPV6 type Bearer
<cr>
Router#cell 0 lte profile create 1 e-ideas chap 65ideas 65ideas ipv4
Warning: You are attempting to modify the attach profile.
Please consult the service provider before doing so.
Modem power cycle required for change to take effect.
PDP Type = IPv4v6
Access Point Name (APN) =
Authentication = NONE
Profile 1 already exists with above parameters. Do you want to overwrite? [confirm]
Profile 1 will be overwritten with the following values:
PDP type = IPv4
APN = e-ideas
Username = 65ideas
Password = 65ideas
Authentication = CHAP
Are you sure? [confirm]
Profile 1 written to modem
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface cell ?
<0-1> Cellular interface number
Router(config)#interface cell 0
Router(config-if)#ip address ?
A.B.C.D IP address
negotiated IP Address negotiated over PPP
pool IP Address autoconfigured from a local DHCP pool
Router(config-if)#ip address negotiated
Router(config-if)#encapsulation ?
bstun Block Serial tunneling (BSTUN)
ppp Point-to-Point protocol
raw-tcp Raw socket TCP
raw-udp Raw socket UDP
scada SCADA
slip Serial Line IP
Router(config-if)#encapsulation slip
Router(config-if)#dialer ?
callback-secure Enable callback security
enable-timeout Set length of time an interface stays down before it
is available for dialing
fast-idle Set idle time before disconnecting line with an
unusually high level of contention
hold-queue Configure output hold queue
idle-timeout Specify idle timeout before disconnecting line
in-band Set v.25bis dialing for interface
map Define multiple dial-on-demand numbers
mult-map-same-name Multiple maps same remote name
order Specify order of choosing dialstrings
pool-member Specify dialer pool membership
priority Specify priority for use in dialer group
redial Configure redial for this interface
rotary-group Add to a dialer rotary group
snapshot Enable snapshot address for dialer profile
string Specify telephone number to be passed to DCE device
vpdn Enable vpdn dial
wait-for-carrier-time How long the router will wait for carrier
wait-for-line-protocol Time the router will wait for the line protocol to
come up
watch-group Assign interface to dialer-watch-list
Router(config-if)#dialer in-band
Router(config-if)#
*Apr 1 14:47:23.211: %CISCO800-2-MODEM_DOWN: Cellular0 modem is now DOWN.
*Apr 1 14:48:00.563: %CISCO800-2-MODEM_UP: Cellular0 modem is now UP
Modem radio has been turned on
Router(config-if)#dialer-group ?
<1-128> Dialer list number
Router(config-if)#dialer-group 1
Router(config-if)#ip nat outside
Router(config-if)#
*Apr 1 14:49:25.947: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI0, changed state to up
Router(config)#dialer-list ?
<1-128> Dialer group number
Router(config)#dialer-list 1 ?
protocol Permit or Deny based on protocols
Router(config)#dialer-list 1 protocol ?
bridge Bridging
ip IP
ipv6 IPv6
llc2 LLC2
netbios NETBIOS
Router(config)#dialer-list 1 protocol ip ?
deny Deny specified protocol
list Add access list to dialer list
permit Permit specified protocol
Router(config)#dialer-list 1 protocol ip permit // IP INTERESTING TRAFFIC
Router(config)#ip route 0.0.0.0 0.0.0.0 cellular ?
<0-1> Cellular interface number
Router(config)#ip route 0.0.0.0 0.0.0.0 cellular 0 // DEFAULT STATIC ROUTE TO HOP CELL 0
INTERFACE
*Apr 1 14:53:39.031: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Apr 1 14:53:40.031: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Apr 1 14:54:08.051: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
Router(config)#interface vlan1
Router(config-if)#ip address 10.1.1.1 255.255.255.0
Router(config-if)#ip nat inside
Router(config-if)#exit
Router(config)#access-list 1 ?
deny Specify packets to reject
permit Specify packets to forward
remark Access list entry comment
Router(config)#access-list 1 permit ?
Hostname or A.B.C.D Address to match
any Any source host
host A single host address
Router(config)#access-list 1 permit 10.1.1.0 0.0.0.255
Router(config)#ip nat ?
Stateful Stateful NAT configuration commands
create Create flow entries
inside Inside address translation
log NAT Logging
outside Outside address translation
piggyback-support NAT Piggybacking Support
pool Define pool of addresses
portmap Define portmap of portranges
service Special translation for application using non-standard
port
sip-sbc SIP Session Border Controller commands
source Source address translation
translation NAT translation entry configuration
Router(config)#ip nat inside ?
destination Destination address translation
source Source address translation
Router(config)#ip nat inside source ?
list Specify access list describing local addresses
route-map Specify route-map
static Specify static local->global mapping
Router(config)#ip nat inside source list ?
<1-2699> Access list number for local addresses
WORD Access list name for local addresses
Router(config)#ip nat inside source list 1 ?
interface Specify interface for global address
pool Name pool of global addresses
Router(config)#ip nat inside source list 1 interface ?
Async Async interface
Auto-Template Auto-Template interface
BDI Bridge-Domain interface
BVI Bridge-Group Virtual Interface
CDMA-Ix CDMA Ix interface
CTunnel CTunnel interface
Cellular Cellular WAN interface
Dialer Dialer interface
Ethernet IEEE 802.3
FastEthernet FastEthernet IEEE 802.3
GMPLS MPLS interface
GigabitEtheret GigabitEthernet IEEE 802.3z
LISP Locator/ID Separation Protocol Virtual Interface
LongReachEthernet Long-Reach Ethernet interface
Loopback Loopback interface
Lspvif LSP virtual interface
MFR Multilink Frame Relay bundle interface
Multilink Multilink-group interface
Null Null interface
Port-channel Ethernet Channel of interfaces
Tunnel Tunnel interface
Vif PGM Multicast Host interface
Router(config)#ip nat inside source list 1 interface cellular ?
<0-1> Cellular interface number
Router(config)#ip nat inside source list 1 interface cellular 0 ?
no-payload No translation of embedded address/port in the payload
overload Overload an address translation
reversible Allow out->in traffic
vrf Specify vrf
<cr>
Router(config)#ip nat inside source list 1 interface cellular 0 overload // PAT INSIDE USERS USING WAN PUBLIC IP
Router#debug chat
Chat scripts activity debugging is on
Router#debug modem
Modem control/pro activation debugging is on
Router#debug dialer
Dial on demand events debugging is on
Router#debug cellular 0 messages callcontrol
CALLCONTROL debugging is on
Router#
Router#
Router#
*Apr 1 16:18:32.839: TTY0: resume timer type 1 (OK)
*Apr 1 16:18:32.855: TTY0: pause timer type 1 (OK)
*Apr 1 16:18:32.855: TTY0: resume timer type 1 (OK)
*Apr 1 16:18:33.611: TTY0: pause timer type 1 (OK)
*Apr 1 16:18:33.611: TTY0: resume timer type 1 (OK)
Router#
Router#
Router#ping 8.8.8.8
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
*Apr 1 16:18:39.315: TTY0: pause timer type 1 (OK)
*Apr 1 16:18:39.315: Ce0 DDR: place call
*Apr 1 16:18:39.315: Ce0 DDR: Dialing cause ip (s=10.1.1.1, d=8.8.8.8)
*Apr 1 16:18:39.315: Ce0 DDR: Attempting to dial lte
*Apr 1 16:18:39.315: CHAT3: Attempting async line dialer script
*Apr 1 16:18:39.315: CHAT3: Dialing using Modem script: lte & System script: none
*Apr 1 16:18:39.315: CHAT3: process started
*Apr 1 16:18:39.315: CHAT3: Asserting DTR
*Apr 1 16:18:39.315: CHAT3: Chat script lte started
*Apr 1 16:18:39.315: CHAT3: Sending string: AT!CALL
*Apr 1 16:18:39.315: CHAT3: Expecting string: OK
*Apr 1 16:18:39.483: cellwan_api_pkt_session_notify: instance id:0 profile:0 status:1
*Apr 1 16:18:39.483: %CELLWAN-2-BEARER_UP: Instance id=0, Default bearer (bearer_id=5) in Cellular0 is now UP
*Apr 1 16:18:39.483: Cellular0 profile 0, session ACTIVE
*Apr 1 16:18:39.483: cellwan_api_pkt_session_notify:connected idb_subunit:0
*Apr 1 16:18:39.723: cellwan_api_handle_profile_ip_addr_get_resp pdn 0 valid 1 length 4 session active 1, profile:0
*Apr 1 16:18:39.723: Sending ok response to line:3
*Apr 1 16:18:39.723: CHAT3: Completed match for expect: OK
*Apr 1 16:18:39.723: CHAT3: Chat script lte finished, status = Success
*Apr 1 16:18:39.723: TTY3: no timer type 1 to destroy
*Apr 1 16:18:39.723: TTY3: no timer type 0 to destroy
*Apr 1 16:18:39.723: TTY3: no timer type 2 to destroy.
*Apr 1 16:18:39.799: Cellular0 DirectIP: Primary DNS address 165.21.83.88 added
*Apr 1 16:18:39.799: Cellular0 DirectIP: Secondary DNS 165.21.100.88 added
*Apr 1 16:18:41.723: %LINK-3-UPDOWN: Interface Cellular0, changed state to up.!!! // WAIT 3 MINS FOR CELL 0 INTERFACE TO BE UP (SCANNING FOR CELL FREQUENCY)
Success rate is 60 percent (3/5), round-trip min/avg/max = 28/118/296 ms
Router#
*Apr 1 16:18:41.723: Ce0 DDR: Dialer statechange to up
*Apr 1 16:18:41.723: Ce0 DDR: Dialer call has been placed
*Apr 1 16:18:41.723: Cellular0 DirectIP: Install negotiated IP interface address 10.233.119.6
*Apr 1 16:18:41.723: Ce0 DDR: dialer protocol up
*Apr 1 16:18:42.723: %LINEPROTO-5-UPDOWN: Line protocol on Interface Cellular0, changed state to up
*Apr 1 16:18:43.671: TTY0: resume timer type 1 (OK)
Router#show cell 0 network
Current System Time = Fri Apr 1 16:20:2 2016
Current Service Status = Normal
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Network = SingTel
Mobile Country Code (MCC) = 525
Mobile Network Code (MNC) = 1
Packet switch domain(PS) state = Attached
Registration state(EMM) = Registered
EMM Sub State = Normal Service
Tracking Area Code (TAC) = 710
Cell ID = 190994691
Router#show cell 0 profile
Profile 1 = ACTIVE* **
--------
PDP Type = IPv4
PDP address = 10.233.119.6
Access Point Name (APN) = e-ideas
Authentication = CHAP
Username: 65ideas
Password: 65ideas
Primary DNS address = 165.21.83.88
Secondary DNS address = 165.21.100.88
* - Default profile
** - LTE attach profile
Configured default profile for active SIM 0 is profile 1.
Router#ping 8.8.8.8
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/84/300 ms
Router#show interface cell0
Cellular0 is up, line protocol is up
Hardware is 4G WWAN Modem - Global (Europe & Australia) Multimode LTE/DC-HSPA+/HSPA+/HSPA/U
Internet address is 10.233.119.6/32
MTU 1500 bytes, BW 50000 Kbit/sec, DLY 100000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation SLIP, loopback not set
Keepalive not supported
Time to interface disconnect: idle 00:00:58
Last input 00:01:01, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/10 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
9 packets input, 828 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
8 packets output, 800 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
Router#
*Apr 1 16:22:12.047: Ce0 DDR: idle timeout
*Apr 1 16:22:12.047: Ce0 DDR: disconnecting call
*Apr 1 16:22:12.047: TTY3: Async Int reset: Dropping DTR
*Apr 1 16:22:14.047: %LINK-5-CHANGED: Interface Cellular0, changed state to reset
*Apr 1 16:22:15.047: %LINEPROTO-5-UPDOWN: Line protocol on Interface Cellular0, changed state to down
*Apr 1 16:22:17.047: api_manage_packet_session Removing IP DNS profile:0 active_prof:0
*Apr 1 16:22:17.047: TTY3: no timer type 0 to destroy
*Apr 1 16:22:17.047: TTY3: no timer type 1 to destroy
*Apr 1 16:22:17.047: TTY3: no timer type 3 to destroy
*Apr 1 16:22:17.047: TTY3: no timer type 4 to destroy
*Apr 1 16:22:17.047: TTY3: no timer type 10 to destroy
*Apr 1 16:22:17.047: TTY3: no timer type 2 to destroy
*Apr 1 16:22:17.047: TTY3: Async Int cleanup: Restoring DTR
*Apr 1 16:22:17.047: Cellular0 DirectIP: Remove negotiated IP interface address
*Apr 1 16:22:17.047: Cellular0 DirectIP: Primary DNS address 165.21.83.88 removed
*Apr 1 16:22:17.047: Cellular0 DirectIP: Secondary DNS address 165.21.100.88 removed
*Apr 1 16:22:17.179: cellwan_api_pkt_session_notify: instance id:0 profile:0 status:0
*Apr 1 16:22:17.179: %CELLWAN-2-BEARER_DELETED: Instance id=0, Default bearer (bearer_id=5) in Cellular0 is now deleted.
*Apr 1 16:22:17.179: Cellular0 profile 0, session INACTIVE
*Apr 1 16:22:17.179: Cellular0 DirectIP: Remove negotiated IP interface address
*Apr 1 16:22:19.047: %LINK-3-UPDOWN: Interface Cellular0, changed state to down
*Apr 1 16:22:29.047: Ce0 DDR: re-enable timeout
Router#show interface cell0
Cellular0 is up (spoofing), line protocol is up (spoofing)
Hardware is 4G WWAN Modem - Global (Europe & Australia) Multimode LTE/DC-HSPA+/HSPA+/HSPA/U
Internet address will be assigned dynamically by the network // THE DHCP IP ADDRESS WAS REMOVED DUE TO IDLE TIMEOUT
MTU 1500 bytes, BW 9 Kbit/sec, DLY 100000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation SLIP, loopback not set
Keepalive not supported
Last input 00:02:35, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/10 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
9 packets input, 828 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
8 packets output, 800 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
Router(config)#interface cell0
Router(config-if)#dialer idle-timeout 0 // TO KEEP THE WWAN/CELL0 INTERFACE UP AND CONNECTED
Router#ping 8.8.8.8
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
*Apr 1 16:23:52.411: %CELLWAN-2-BEARER_UP: Instance id=0, Default bearer (bearer_id=5) in
Cellular0 is now UP.
*Apr 1 16:23:54.651: %LINK-3-UPDOWN: Interface Cellular0, changed state to up
*Apr 1 16:23:55.651: %LINEPROTO-5-UPDOWN: Line protocol on Interface Cellular0, changed state to up.!!!
Success rate is 60 percent (3/5), round-trip min/avg/max = 28/80/180 ms
Router#show interface cell0
Cellular0 is up, line protocol is up
Hardware is 4G WWAN Modem - Global (Europe & Australia) Multimode LTE/DC-HSPA+/HSPA+/HSPA/U
Internet address is 10.233.119.6/32
MTU 1500 bytes, BW 50000 Kbit/sec, DLY 100000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation SLIP, loopback not set
Keepalive not supported
Last input 00:01:14, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/10 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
13 packets input, 1156 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
11 packets output, 1100 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
Below is the basic working config. The LTE profile is not shown.
Router#show run
Building configuration...
Current configuration : 2546 bytes
!
! Last configuration change at 16:37:51 UTC Fri Apr 1 2016
!
version 15.5
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
enable password cisco
!
no aaa new-model
ethernet lmi ce
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
ip cef
no ipv6 cef
!
!
!
!
!
multilink bundle-name authenticated
!
!
chat-script lte "" "AT!CALL" TIMEOUT 20 "OK" // DEFAULT CONFIG
!
!
!
!
!
license udi pid C899G-LTE-GA-K9 sn FCZ20069123
!
!
username cisco privilege 15 password 0 cisco
!
!
!
!
!
controlle lte modem link-recovery rssi onset-threshold -110
lte modem link-recovery monitor-timer 20
lte modem link-recovery wait-timer 10
lte modem link-recovery debounce-count 6
!
!
!
!
!
!
!
!
!
!
!
!
interface Cellular0
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation slip
dialer in-band
dialer idle-timeout 0
dialer string lte // DEFAULT CONFIG
dialer-group 1
!
interface Cellular1
no ip address
encapsulation slip
!
interface FastEthernet0
no ip address
shutdown
duplex auto
speed auto
!
interface GigabitEthernet0
no ip address
!
interface GigabitEthernet1
no ip address
!
interface GigabitEthernet2
no ip address
!
interface GigabitEthernet3
no ip address
!
interface GigabitEthernet4
no ip address
!
interface GigabitEthernet5
no ip address
!
interface GigabitEthernet6
no ip address
!
interface GigabitEthernet7
no ip address
!
interface GigabitEthernet8
no ip address
shutdown
duplex auto
speed auto
!
interface GigabitEthernet9
no ip address
shutdown
duplex auto
speed auto
!
interface Vlan1
ip address 10.1.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
!
ip nat inside source list 1 interface Cellular0 overload
ip route 0.0.0.0 0.0.0.0 Cellular0
!
dialer-list 1 protocol ip permit
!
access-list 1 permit 10.1.1.0 0.0.0.255
!
control-plane
!
!
!
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
!
mgcp profile default
!
!
!
!
!
!
!
line con 0
password cisco
login
no modem enable
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
stopbits 1
line 3
script dialer lte // DEFAULT CONFIG
no exec
rxspeed 100000000 // DEFAULT CONFIG
txspeed 50000000 // DEFAULT CONFIG
line 8
no exec
rxspeed 100000000
txspeed 50000000
line vty 0 4
password cisco
login
transport input none
!
scheduler allocate 20000 1000
!
end
I got a 14 Mbps download / 22 Mbps upload Speedtest result from the PC connected (wired) behind the Cisco 4G router. I also tested using a 3G SIM card (used the same SingTel LTE/APN profile) which also worked and got almost the same Speedtest result.
Below are some helpful troubleshooting commands and remotely check router LED status.
Router#show platform led
LED STATUS:
==========
POWER : GREEN
PPP : OFF
POE OK : OFF
xDSL CD : OFF
xDSL DATA : OFF
VPN : OFF
ISDN B1 DATA : OFF
ISDN B2 DATA : OFF
RSSI : GREEN(2 BLINK)
GPS : OFF
SIM slot0 : GREEN
SIM slot1 : OFF
Service : GREEN(2 BLINK)
Router#show controller cellular 0
Interface Cellular0
4G WWAN Modem - Global (Europe & Australia) Multimode LTE/DC-HSPA+/HSPA+/HSPA/U
Cellular modem configuration
======================================
Modem is recognized as valid
manufacture id: 0x00001199 product id: 0x000068C0
Sierra Wireless Direct IP MC7304 modem
Modem Uplink Speed = 384 kbit.
Modem Downlink Speed = 384 kbit.
GPS Feature: enabled
GPS State: GPS disabled
GPS Mode: disabled
GPS Port selected: Dedicated GPS port
Cellular Dual SIM details:
---------------------------
SIM 0 is present
SIM 0 is active SIM
Cellular Dual SIM register:
Dual SIM Control Register 6A
Dual SIM Interrupt Register 4
Dual SIM Mask Interrupt Register C6
Modem Management Statistics
---------------------------
Modem resets = 12
Modem user initiated resets = 0
Modem user initiated power-cycles = 0
Modem timeouts = 10
Modem parameters at the last timeout:
SDK API return code was 50462720(0x3020000)
Link recovery is ON
Registration check is ON
RSSI threshold value is -110 dBm
Monitor Timer value is 20 seconds
Wait Timer value is 10 seconds
Debounce Count value is 6
Last known modem state = 'application' mode
AT Command Port = /dev/ttyUSB2
NMEA Port = /dev/ttyUSB1
DM Port = /dev/ttyUSB0
DIP MDM link status retry count = 0 pdp context = 0
DIP MDM link up pending = 0 pdp context = 0
DIP MDM link status retry count = 0 pdp context = 1
DIP MDM link up pending = 0 pdp context = 1
DIP MDM link status retry count = 0 pdp context = 2
DIP MDM link up pending = 0 pdp context = 2
IDB with pending DIP call: Cellular0
IDB Cellular0: DIP profile id = 1
IDB Cellular1: DIP profile id = 255
RSSI LED : 3-blink Green
Service LED : 2-blink Green
SIM LED : Slot0 - Green
GPS LED : Off
GPS NMEA port = Disabled (Stream OFF)
DM port = Disabled
Modem Callback Statistics
---------------------------
PacketServiceCallback_count 1
DataBearerCallback_count 0
DormancyStatusCallback_count 0
PowerCallback_count 0
ByteTotalsCallback_count 0
iByteTotalsCallback_count 0
PacketsCountCallback_count 0
iPacketsCountCallback_count 0
ActivationStatusCallback_count 0
MobileIPStatusCallback_count 0
RoamingIndicatorCallback_count 0
DataCapabilitiesCallback_count 0
SignalStrengthCallback_count 0
iSignalStrengthCallback_count 0
RFInfoCallback_count 0
LURejectCallback_count 0
NewSMSCallback_count 0
SLQSSMSEventCallback_count 0
NMEACallback_count 0
PDSStateCallback_count 1
CATEventCallback_count 0
iCATEventCallback_count 0
DeviceStateChangeCbk_count 0
FwDldCompletionCbk_count 0
SLQSOMADMAlertCallback_count 0
OMADMStateCallback_count 0
SLQSServingSystemCallback_count 1955
SLQSBandPreferenceCbk_count 0
USSDReleaseCallback_count 0
USSDNotificationCallback_count 0
SLQSSignalStrengthsCallback_count 0
iSLQSSignalStrengthsCallback_count 0
SLQSSDKTerminatedCallback_count 0
SLQSTransLayerInfoCallback_count 0
SLQSTransNWRegInfoCallback_count 0
SLQSSysSelectionPrefCallBack_count 0
NotifySessionStateDisconnect_count 0
WdsEventCallback_count 1679
HeartbeatModemStatisticsCallback_count 5905
0 input aborts on receiving flag sequence
0 throttles, 0 enables
0 overruns, 0 CRC errors
0 resource errors, 0 incomp frame errors
0 input drops
0 transmitter underruns
Cellular UBOOT F/W Info
========================
UBOOT Version = 2.0
UBOOT Build Date = Sep 21 2014
C800 Cellular Linux F/W Info
=============================
Linux Kernel:
Firmware Build Date = Nov 2 2016
Firmware Version = 2.0
Linux Rootfs:
Firmware Build Date = Nov 2 2016
Firmware Version = 2.0
The Current Modem SDK Version is 03.03.04.03
Modem USB-Serial Driver Version is GobiSerial <unknown>
Modem USB-Net Driver Version is GobiNet <unknown>
Cellular Statistics
===========================
IPC Counters
--------------------------------
IPC Tx :646094 IPC Rx AT commands :108
IPC Tx without Ack :646066 IPC Rx Mgmt & API :876099
IPC Tx with Ack :28 :
IPC Tx Err Invalid Sig :0 :
IPC Tx Err Q full :0 :
IPC Tx Err Q null pak :0 :
IPC Tx Err Q null bool :0 :
IPC Tx Err Bool Create fl:0 :
IPC Tx Err Ack Fail :0 :
IPC Tx Pending :0 :
IPC Buffers in Use :257 :
Data Counters
--------------------------------
Data Tx Packets :30764 Data Rx Packets :36307
Data Tx Bytes :5444613 Data Rx Bytes :36408144
Host Data Statistics from Linux
--------------------------------
Statistics for PDN 0:
Data Tx Packets :30764 Data Rx Packets :36307
IP pkts dropped :0
Statistics for PDN 1:
Data Tx Packets :0 Data Rx Packets :0
IP pkts dropped :0
MCC per channel information (MAX 9)
Core 0 Channel Bitmaps:
IOS: Tx Data Ready Bitmap 0x0, Tx Complete Bitmap 0x1FF
Core 0 Counters:
===================
[Chan 0]
============
Data Tx Packets No Partic:646094 Data Rx Packets :876271
Data Tx Bytes No Particle:12926942 Data Rx Bytes :72269497
Data Tx Packets Single Pa:0 :
Data Tx Bytes Single Part:0 :
Data Tx Packets Multi Par:0 :
Data Tx Bytes Multi Parti:0 :
Tx Errors :0 Rx Errors :0
[Chan 1]
============
Data Tx Packets No Partic:30764 Data Rx Packets :36371
Data Tx Bytes No Particle:5444613 Data Rx Bytes :36408144
Data Tx Packets Single Pa:0 :
Data Tx Bytes Single Part:0 :
Data Tx Packets Multi Par:0 :
Data Tx Bytes Multi Parti:0 :
Tx Errors :0 Rx Errors :0
[Chan 2]
============
Data Tx Packets No Partic:0 Data Rx Packets :64
Data Tx Bytes No Particle:0 Data Rx Bytes :0
Data Tx Packets Single Pa:0 :
Data Tx Bytes Single Part:0 :
Data Tx Packets Multi Par:0 :
Data Tx Bytes Multi Parti:0 :
Tx Errors :0 Rx Errors :0
[Chan 3]
============
Data Tx Packets No Partic:29890 Data Rx Packets :6
Data Tx Bytes No Particle:11565468 Data Rx Bytes :468
Data Tx Packets Single Pa:0 :
Data Tx Bytes Single Part:0 :
Data Tx Packets Multi Par:0 :
Data Tx Bytes Multi Parti:0 :
Tx Errors :0 Rx Errors :0
[Chan 4]
============
Data Tx Packets No Partic:0 Data Rx Packets :64
Data Tx Bytes No Particle:0 Data Rx Bytes :0
Data Tx Packets Single Pa:0 :
Data Tx Bytes Single Part:0 :
Data Tx Packets Multi Par:0 :
Data Tx Bytes Multi Parti:0 :
Tx Errors :0 Rx Errors :0
[Chan 5]
============
Data Tx Packets No Partic:0 Data Rx Packets :64
Data Tx Bytes No Particle:0 Data Rx Bytes :0
Data Tx Packets Single Pa:0 :
Data Tx Bytes Single Part:0 :
Data Tx Packets Multi Par:0 :
Data Tx Bytes Multi Parti:0 :
Tx Errors :0 Rx Errors :0
[Chan 6]
============
Data Tx Packets No Partic:0 Data Rx Packets :64
Data Tx Bytes No Particle:0 Data Rx Bytes :0
Data Tx Packets Single Pa:0 :
Data Tx Bytes Single Part:0 :
Data Tx Packets Multi Par:0 :
Data Tx Bytes Multi Parti:0 :
Tx Errors :0 Rx Errors :0
[Chan 7]
============
Data Tx Packets No Partic:0 Data Rx Packets :64
Data Tx Bytes No Particle:0 Data Rx Bytes :0
Data Tx Packets Single Pa:0 :
Data Tx Bytes Single Part:0 :
Data Tx Packets Multi Par:0 :
Data Tx Bytes Multi Parti:0 :
Tx Errors :0 Rx Errors :0
[Chan 8]
============
Data Tx Packets No Partic:0 Data Rx Packets :64
Data Tx Bytes No Particle:0 Data Rx Bytes :0
Data Tx Packets Single Pa:0 :
Data Tx Bytes Single Part:0 :
Data Tx Packets Multi Par:0 :
Data Tx Bytes Multi Parti:0 :
Tx Errors :0 Rx Errors :0
Core 0 TX Ring information:
==========================
[Chan 0] txring=0x17C00008, txr shadow=0x211E944C, tx_head=17, tx_tail=17, tandem_tail=49, tx_count=0
Core 0 Chan 0 TX ring entries:
Index TxR-Addr Buff-Addr Size Status
00 0x17C00008 0x0 00000 0x0000
01 0x17C00018 0x0 00000 0x0000
02 0x17C00028 0x0 00000 0x0000
03 0x17C00038 0x0 00000 0x0000
04 0x17C00048 0x0 00000 0x0000
05 0x17C00058 0x0 00000 0x0000
<OUTPUT TRUCATED>
These are the ports at the back of the router. It has dual 4G antennas, a built-in 8-port GigabitEthernet switch (GE ports 0-7), dual GigabitEthernet WAN ports (GE WAN ports 8 and 9) with the option for fiber SFP for one GE WAN. The dual SIM card slot is covered by a metal plate and you'll need a flathead screwdriver to press it down and pull it off.
Once the metal cover is removed, take note of the orientation for inserting the SIM card using the SIM icon/drawing beside S0 and S1.
There is also an option to use an extended antenna (4G-AE010-R) to get a better signal.
Once the router completely boots up, take note of the LED lights in front such as the SIM card slot number, the signal strength (RSSI) and if LTE/WWAN is active.
System Bootstrap, Version 15.4(3r)M1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2014 by cisco Systems, Inc.
bad checksum, p_nvram 0x415d70
Correcting the backup nv_flash
Total memory size = 1024 MB
C899G-LTE-GA-K9 platform with 1048576 Kbytes of main memory
Main memory is configured to 32 bit mode
Readonly ROMMON initialized
IOS Image Load Test
___________________
Digitally Signed Production Software
Self decompressing the image :
##################################################################################################
##################################################################################################
##################################################################################################
##################################################################################################
##################################################################################################
##################################################################################################
##################################################################################################
######################################################################################## [OK]
*** No sreloc section
Smart Init is enabled
smart init is sizing iomem
TYPE MEMORY_REQ
Onboard devices &
buffer pools 0x03AECEC0
-----------------------------------------------
TOTAL: 0x03AECEC0
Rounded IOMEM up to: 58Mb.
Using 6 percent iomem. [58Mb/896Mb]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C800 Software (C800-UNIVERSALK9-M), Version 15.5(3)M, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Wed 22-Jul-15 23:59 by prod_rel_team
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Cisco C899G-LTE-GA-K9 (revision 1.0) with 857164K/60339K bytes of memory.Installed image archive
Processor board ID FCZ20069123
1 FastEthernet interface
10 Gigabit Ethernet interfaces
3 terminal lines
1 Virtual Private Network (VPN) Module
2 Cellular interfaces
DRAM configuration is 32 bits wide
255K bytes of non-volatile configuration memory.
1000944K bytes of ATA System CompactFlash (Read/Write)
%Error opening tftp://255.255.255.255/network-confg (Socket error)
%Error opening tftp://255.255.255.255/cisconet.cfg (Socket error)
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]: no
Press RETURN to get started!
*Jan 2 00:00:01.031: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name = c800 Next reboot level = advipservices and License = advipservices
*Apr 1 14:25:17.839: c3600_scp_set_dstaddr2_idb(184)add = 80 name is Embedded-Service-Engine0
*Apr 1 14:25:18.127: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed to: Initialized
*Apr 1 14:25:18.127: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed to: Enabled
*Apr 1 14:25:34.311: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to up
*Apr 1 14: %LINK-3-UPDOWN: Interface GigabitEthernet8, changed state to up
*Apr 1 14:25:34.311: %LINK-3-UPDOWN: Interface GigabitEthernet9, changed state to up
*Apr 1 14:25:34.311: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Apr 1 14:25:35.011: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
*Apr 1 14:25:35.311: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet8, changed state to down
*Apr 1 14:25:35.311: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet9, changed state to down
*Apr 1 14:25:35.311: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Apr 1 14:25:37.011: %LINK-3-UPDOWN: Interface GigabitEthernet9, changed state to down
*Apr 1 14:25:37.011: %LINK-3-UPDOWN: Interface GigabitEthernet8, changed state to down
*Apr 1 14:26:19.091: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse from
(tftp://255.255.255.255/network-confg) failed
*Apr 1 14:26:19.167: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse from
(tftp://255.255.255.255/cisconet.cfg) failed
*Apr 1 14:26:28.379: %LINK-5-CHANGED: Interface FastEthernet0, changed state to administratively down
*Apr 1 14:26:28.955: %LINK-5-CHANGED: Interface GigabitEthernet8, changed state to
administratively down
*Apr 1 14:26:28.983: %LINK-5-CHANGED: Interface GigabitEthernet9, changed state to
administratively down
*Apr 1 14:26:29.379: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
*Apr 1 14:26:33.667: %LINK-3-UPDOWN: Interface Ethernet10, changed state to up
*Apr 1 14:26:34.815: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet10, changed state to up
*Apr 1 14:26:36.399: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Apr 1 14:26:36.399: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1, changed state to down
*Apr 1 14:26:36.619: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2, changed state to down
*Apr 1 14:26:36.619: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet3, changed state to down
*Apr 1 14:26:36.619: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet4, changed state to down
*Apr 1 14:26:36.619: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet5, changed state to down
*Apr 1 14:26:36.619: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet6, changed state to down
*Apr 1 14:26:36.619: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet7, changed state to down
*Apr 1 14:26:38.039: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C800 Software (C800-UNIVERSALK9-M), Version 15.5(3)M, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Wed 22-Jul-15 23:59 by prod_rel_team
*Apr 1 14:26:38.255: ifs_open failed, path flash:1:/env_vars errno 2574
*Apr 1 14:26:38.347: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Apr 1 14:26:38.347: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF
*Apr 1 14:26:43.575: %SECONDCORE-5-BOOTSTAGE: ROMMON on 2nd core UP
*Apr 1 14:26:43.587: %SECONDCORE-5-BOOTSTAGE: BOOTLOADER on 2nd core UP
*Apr 1 14:26:47.719: %SECONDCORE-5-BOOTSTAGE: LINUX on 2nd core UP
Router>show ip interface brief
Interface IP-Address OK? Method Status Protocol
Cellular0 unassigned YES unset down down
Cellular1 unassigned YES unset down down
FastEthernet0 unassigned YES unset administratively down down
GigabitEthernet0 unassigned YES unset down down
GigabitEthernet1 unassigned YES unset down down
GigabitEthernet2 unassigned YES unset down down
GigabitEthernet3 unassigned YES unset down down
GigabitEthernet4 unassigned YES unset down down
GigabitEthernet5 unassigned YES unset down down
GigabitEthernet6 unassigned YES unset down down
GigabitEthernet7 unassigned YES unset down down
GigabitEthernet8 unassigned YES unset administratively down down
GigabitEthernet9 unassigned YES unset administratively down down
Vlan1 unassigned YES unset down down
Router>
Router>show version
Cisco IOS Software, C800 Software (C800-UNIVERSALK9-M), Version 15.5(3)M, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Wed 22-Jul-15 23:59 by prod_rel_team
ROM: System Bootstrap, Version 15.4(3r)M1, RELEASE SOFTWARE (fc1)
Router uptime is 2 minutes
System returned to ROM by power-on
System image file is "flash:c800-universalk9-mz.SPA.155-3.M.bin"
Last reload type: Normal Reload
Last reload reason: power-on
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Cisco C899G-LTE-GA-K9 (revision 1.0) with 857164K/60339K bytes of memory.
Processor board ID FCZ20069123
1 FastEthernet interface
10 Gigabit Ethernet interfaces
3 terminal lines
1 Virtual Private Network (VPN) Module
2 Cellular interfaces
DRAM configuration is 32 bits wide
255K bytes of non-volatile configuration memory.
1000944K bytes of ATA System CompactFlash (Read/Write)
License Info:
License UDI:
-------------------------------------------------
Device# PID SN
-------------------------------------------------
*1 C899G-LTE-GA-K9 FCZ20069123
License Information for 'c800'
License Level: advipservices Type: Permanent
Next reboot license Level: advipservices
Configuration register is 0x2102
Router>
*Apr 1 14:27:34.823: %CISCO800-2-MODEM_UP: Cellular0 modem is now UP
Router#show ip interface brief
Interface IP-Address OK? Method Status Protocol
Cellular0 unassigned YES unset up up
Cellular1 unassigned YES unset down down
FastEthernet0 unassigned YES unset administratively down down
GigabitEthernet0 unassigned YES unset down down
GigabitEthernet1 unassigned YES unset down down
GigabitEthernet2 unassigned YES unset down down
GigabitEthernet3 unassigned YES unset down down
GigabitEthernet4 unassigned YES unset down down
GigabitEthernet5 unassigned YES unset down down
GigabitEthernet6 unassigned YES unset down down
GigabitEthernet7 unassigned YES unset down down
GigabitEthernet8 unassigned YES unset administratively down down
GigabitEthernet9 unassigned YES unset administratively down down
Vlan1 unassigned YES unset down down
Router>enable
Router#show cell ?
<0-1> Cellular interface number
Router#show cell 0 ?
all Display all the information
connection Current active connection and statistics
gps Cellular gps information
hardware Cellular modem hardware information
logs Modem logging information
microcode Cellular microcode information
network Cellular network information
oma-dm LTE OMA DM information
profile Profile information in the modem
qos Current QoS configuration and statistics
radio Cellular modem radio information
security Modem security status
sms SMS information
Router#show cell 0 radio
Radio power mode = ON
LTE Rx Channel Number = 3250
LTE Tx Channel Number = 19300
LTE Band = 7
LTE Bandwidth = 20 MHz
Current RSSI = -63 dBm // STRONG SIGNAL
Current RSRP = -91 dBm
Current RSRQ = -9 dB
Current SNR = 6.8 dB
Radio Access Technology(RAT) Preference = AUTO
Radio Access Technology(RAT) Selected = LTE
Below is a useful RSSI reference chart.
Router#show cell 0 network
Current System Time = Fri Apr 1 14:32:36 2016
Current Service Status = Normal
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Network = SingTel
Mobile Country Code (MCC) = 525
Mobile Network Code (MNC) = 1
Packet switch domain(PS) state = Attached
Registration state(EMM) = Registered
EMM Sub State = Normal Service
Tracking Area Code (TAC) = 710
Cell ID = 188590849
Router#show cell 0 profile
Profile 1 = INACTIVE* **
--------
PDP Type = IPv4v6
Access Point Name (APN) =
Authentication = None
* - Default profile
** - LTE attach profile
Configured default profile for active SIM 0 is profile 1.
Router#show cell 0 security
Active SIM = 0 // WILL DISPLAY A "1" IF 4G SIM CARD IS INSERTED IN SIM1 SLOT
SIM switchover attempts = 0
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of CHV1 Retries remaining = 3
Router#show cell 0 all
Hardware Information
====================
Modem Firmware Version = SWI9X15C_05.05.58.00
Modem Firmware built = 2015/03/04 21:30:23
Hardware Version = 1.0
Device Model ID: MC7304
Package Identifier ID: 1102029_9903299_MC7304_05.05.58.00_00_Cisco_005.010_000
International Mobile Subscriber Identity (IMSI) = 525016118316xxx
International Mobile Equipment Identity (IMEI) = 352761060732xxx
Integrated Circuit Card ID (ICCID) = 8965011301141677xxx
Mobile Subscriber Integrated Services
Digital Network-Number (MSISDN) = 6591133xxx
Current Modem Temperature = 35 deg C
PRI SKU ID = 9903299, PRI version = 05.10, Carrier = 1
Profile Information
====================
Profile 1 = INACTIVE* **
--------
PDP Type = IPv4v6
Access Point Name (APN) =
Authentication = None
* - Default profile
** - LTE attach profile
Configured default profile for active SIM 0 is profile 1.
Data Connection Information
===========================
Profile 1, Packet Session Status = INACTIVE
Profile 2, Packet Session Status = INACTIVE
Profile 3, Packet Session Status = INACTIVE
Profile 4, Packet Session Status = INACTIVE
Profile 5, Packet Session Status = INACTIVE
Profile 6, Packet Session Status = INACTIVE
Profile 7, Packet Session Status = INACTIVE
Profile 8, Packet Session Status = INACTIVE
Profile 9, Packet Session Status = INACTIVE
Profile 10, Packet Session Status = INACTIVE
Profile 11, Packet Session Status = INACTIVE
Profile 12, Packet Session Status = INACTIVE
Profile 13, Packet Session Status = INACTIVE
Profile 14, Packet Session Status = INACTIVE
Profile 15, Packet Session Status = INACTIVE
Profile 16, Packet Session Status = INACTIVE
Network Information
===================
Current System Time = Fri Apr 1 14:36:37 2016
Current Service Status = Normal
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Network = SingTel
Mobile Country Code (MCC) = 525
Mobile Network Code (MNC) = 1
Packet switch domain(PS) state = Attached
Registration state(EMM) = Registered
EMM Sub State = Normal Service
Tracking Area Code (TAC) = 710
Cell ID = 188590849
Radio Information
=================
Radio power mode = ON
LTE Rx Channel Number = 3250
LTE Tx Channel Number = 19300
LTE Band = 7
LTE Bandwidth = 20 MHz
Current RSSI = -63 dBm
Current RSRP = -91 dBm
Current RSRQ = -9 dB
Current SNR = 4.4 dB
Radio Access Technology(RAT) Preference = AUTO
Radio Access Technology(RAT) Selected = LTE
Modem Security Information
==========================
Active SIM = 0
SIM switchover attempts = 0
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of CHV1 Retries remaining = 3
GPS Information
==========================
GPS Info
-------------
GPS Feature: enabled
GPS Port Selected: Dedicated GPS port
GPS State: GPS disabled
SMS Information
===============
Incoming Message Information
----------------------------
SMS stored in modem = 0
SMS archived since booting up = 0
Total SMS deleted since booting up = 0
Storage records allocated = 25
Storage records used = 0
Number of callbacks triggered by SMS = 0
Number of successful archive since booting up = 0
Number of failed archive since booting up = 0
Outgoing Message Information
----------------------------
Total SMS sent successfully = 0
Total SMS send failure = 0
Number of outgoing SMS pending = 0
Number of successful archive since booting up = 0
Number of failed archive since booting up = 0
Last Outgoing SMS Status = SUCCESS
Copy-to-SIM Status = 0x0
Send-to-Network Status = 0x0
Report-Outgoing-Message-Number:
Reference Number = 0
Result Code = 0x0
Diag Code = 0x0 0x0 0x0 0x0 0x0
SMS Archive URL =
Error Information
=================
This command is not supported on this platform.
Modem Crashdump Information
===========================
Modem crashdump logging: off
Router#show interface cell0
Cellular0 is up (spoofing), line protocol is up (spoofing)
Hardware is 4G WWAN Modem - Global (Europe & Australia) Multimode LTE/DC-HSPA+/HSPA+/HSPA/U
Internet address will be assigned dynamically by the network
MTU 1500 bytes, BW 9 Kbit/sec, DLY 100000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation SLIP, loopback not set
Keepalive not supported
Last input 00:02:35, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/10 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
9 packets input, 828 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
8 packets output, 800 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
I've used the SingTel Acces Point Name (APN) settings below for the LTE profile configuration (also works with a SingTel 3G SIM card). This link provides the APN info for Singapore mobile carriers while this link provides the APN for mobile carriers in different countries.
Router#cell ?
<0-1> Cellular interface number
Router#cell 0 ?
lte LTE Technology Commands
Router#cell 0 lte ?
oma-dm Open Mobile Alliance Device Management
plmn PLMN Commands
prl-region View/set PRL region
profile LTE Profile management commands
sim SIM card commands
sms SMS Commands
technology LTE Technology Preferences
Router#cell 0 lte profile ?
create Create/Edit a Profile
delete Delete a profile
Router#cell 0 lte profile create ?
<1-16> Profile Number
Router#cell 0 lte profile create 1 ?
WORD Access Point Name
<cr>
Router#cell 0 lte profile create 1 e-ideas ?
chap CHAP authentication only
none No authentication
pap PAP authentication only
pap_chap PAP or CHAP authentication
<cr>
Router#cell 0 lte profile create 1 e-ideas chap ?
WORD Username
Router#cell 0 lte profile create 1 e-ideas chap 65ideas ?
WORD Password
<cr>
Router#cell 0 lte profile create 1 e-ideas chap 65ideas 65ideas ?
ipv4 IPv4 type Bearer
ipv4v6 IPV4V6 type Bearer
ipv6 IPV6 type Bearer
<cr>
Router#cell 0 lte profile create 1 e-ideas chap 65ideas 65ideas ipv4
Warning: You are attempting to modify the attach profile.
Please consult the service provider before doing so.
Modem power cycle required for change to take effect.
PDP Type = IPv4v6
Access Point Name (APN) =
Authentication = NONE
Profile 1 already exists with above parameters. Do you want to overwrite? [confirm]
Profile 1 will be overwritten with the following values:
PDP type = IPv4
APN = e-ideas
Username = 65ideas
Password = 65ideas
Authentication = CHAP
Are you sure? [confirm]
Profile 1 written to modem
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface cell ?
<0-1> Cellular interface number
Router(config)#interface cell 0
Router(config-if)#ip address ?
A.B.C.D IP address
negotiated IP Address negotiated over PPP
pool IP Address autoconfigured from a local DHCP pool
Router(config-if)#ip address negotiated
Router(config-if)#encapsulation ?
bstun Block Serial tunneling (BSTUN)
ppp Point-to-Point protocol
raw-tcp Raw socket TCP
raw-udp Raw socket UDP
scada SCADA
slip Serial Line IP
Router(config-if)#encapsulation slip
Router(config-if)#dialer ?
callback-secure Enable callback security
enable-timeout Set length of time an interface stays down before it
is available for dialing
fast-idle Set idle time before disconnecting line with an
unusually high level of contention
hold-queue Configure output hold queue
idle-timeout Specify idle timeout before disconnecting line
in-band Set v.25bis dialing for interface
map Define multiple dial-on-demand numbers
mult-map-same-name Multiple maps same remote name
order Specify order of choosing dialstrings
pool-member Specify dialer pool membership
priority Specify priority for use in dialer group
redial Configure redial for this interface
rotary-group Add to a dialer rotary group
snapshot Enable snapshot address for dialer profile
string Specify telephone number to be passed to DCE device
vpdn Enable vpdn dial
wait-for-carrier-time How long the router will wait for carrier
wait-for-line-protocol Time the router will wait for the line protocol to
come up
watch-group Assign interface to dialer-watch-list
Router(config-if)#dialer in-band
Router(config-if)#
*Apr 1 14:47:23.211: %CISCO800-2-MODEM_DOWN: Cellular0 modem is now DOWN.
*Apr 1 14:48:00.563: %CISCO800-2-MODEM_UP: Cellular0 modem is now UP
Modem radio has been turned on
Router(config-if)#dialer-group ?
<1-128> Dialer list number
Router(config-if)#dialer-group 1
Router(config-if)#ip nat outside
Router(config-if)#
*Apr 1 14:49:25.947: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI0, changed state to up
Router(config)#dialer-list ?
<1-128> Dialer group number
Router(config)#dialer-list 1 ?
protocol Permit or Deny based on protocols
Router(config)#dialer-list 1 protocol ?
bridge Bridging
ip IP
ipv6 IPv6
llc2 LLC2
netbios NETBIOS
Router(config)#dialer-list 1 protocol ip ?
deny Deny specified protocol
list Add access list to dialer list
permit Permit specified protocol
Router(config)#dialer-list 1 protocol ip permit // IP INTERESTING TRAFFIC
Router(config)#ip route 0.0.0.0 0.0.0.0 cellular ?
<0-1> Cellular interface number
Router(config)#ip route 0.0.0.0 0.0.0.0 cellular 0 // DEFAULT STATIC ROUTE TO HOP CELL 0
INTERFACE
*Apr 1 14:53:39.031: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Apr 1 14:53:40.031: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Apr 1 14:54:08.051: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
Router(config)#interface vlan1
Router(config-if)#ip address 10.1.1.1 255.255.255.0
Router(config-if)#ip nat inside
Router(config-if)#exit
Router(config)#access-list 1 ?
deny Specify packets to reject
permit Specify packets to forward
remark Access list entry comment
Router(config)#access-list 1 permit ?
Hostname or A.B.C.D Address to match
any Any source host
host A single host address
Router(config)#access-list 1 permit 10.1.1.0 0.0.0.255
Router(config)#ip nat ?
Stateful Stateful NAT configuration commands
create Create flow entries
inside Inside address translation
log NAT Logging
outside Outside address translation
piggyback-support NAT Piggybacking Support
pool Define pool of addresses
portmap Define portmap of portranges
service Special translation for application using non-standard
port
sip-sbc SIP Session Border Controller commands
source Source address translation
translation NAT translation entry configuration
Router(config)#ip nat inside ?
destination Destination address translation
source Source address translation
Router(config)#ip nat inside source ?
list Specify access list describing local addresses
route-map Specify route-map
static Specify static local->global mapping
Router(config)#ip nat inside source list ?
<1-2699> Access list number for local addresses
WORD Access list name for local addresses
Router(config)#ip nat inside source list 1 ?
interface Specify interface for global address
pool Name pool of global addresses
Router(config)#ip nat inside source list 1 interface ?
Async Async interface
Auto-Template Auto-Template interface
BDI Bridge-Domain interface
BVI Bridge-Group Virtual Interface
CDMA-Ix CDMA Ix interface
CTunnel CTunnel interface
Cellular Cellular WAN interface
Dialer Dialer interface
Ethernet IEEE 802.3
FastEthernet FastEthernet IEEE 802.3
GMPLS MPLS interface
GigabitEtheret GigabitEthernet IEEE 802.3z
LISP Locator/ID Separation Protocol Virtual Interface
LongReachEthernet Long-Reach Ethernet interface
Loopback Loopback interface
Lspvif LSP virtual interface
MFR Multilink Frame Relay bundle interface
Multilink Multilink-group interface
Null Null interface
Port-channel Ethernet Channel of interfaces
Tunnel Tunnel interface
Vif PGM Multicast Host interface
Router(config)#ip nat inside source list 1 interface cellular ?
<0-1> Cellular interface number
Router(config)#ip nat inside source list 1 interface cellular 0 ?
no-payload No translation of embedded address/port in the payload
overload Overload an address translation
reversible Allow out->in traffic
vrf Specify vrf
<cr>
Router(config)#ip nat inside source list 1 interface cellular 0 overload // PAT INSIDE USERS USING WAN PUBLIC IP
Router#debug chat
Chat scripts activity debugging is on
Router#debug modem
Modem control/pro activation debugging is on
Router#debug dialer
Dial on demand events debugging is on
Router#debug cellular 0 messages callcontrol
CALLCONTROL debugging is on
Router#
Router#
Router#
*Apr 1 16:18:32.839: TTY0: resume timer type 1 (OK)
*Apr 1 16:18:32.855: TTY0: pause timer type 1 (OK)
*Apr 1 16:18:32.855: TTY0: resume timer type 1 (OK)
*Apr 1 16:18:33.611: TTY0: pause timer type 1 (OK)
*Apr 1 16:18:33.611: TTY0: resume timer type 1 (OK)
Router#
Router#
Router#ping 8.8.8.8
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
*Apr 1 16:18:39.315: TTY0: pause timer type 1 (OK)
*Apr 1 16:18:39.315: Ce0 DDR: place call
*Apr 1 16:18:39.315: Ce0 DDR: Dialing cause ip (s=10.1.1.1, d=8.8.8.8)
*Apr 1 16:18:39.315: Ce0 DDR: Attempting to dial lte
*Apr 1 16:18:39.315: CHAT3: Attempting async line dialer script
*Apr 1 16:18:39.315: CHAT3: Dialing using Modem script: lte & System script: none
*Apr 1 16:18:39.315: CHAT3: process started
*Apr 1 16:18:39.315: CHAT3: Asserting DTR
*Apr 1 16:18:39.315: CHAT3: Chat script lte started
*Apr 1 16:18:39.315: CHAT3: Sending string: AT!CALL
*Apr 1 16:18:39.315: CHAT3: Expecting string: OK
*Apr 1 16:18:39.483: cellwan_api_pkt_session_notify: instance id:0 profile:0 status:1
*Apr 1 16:18:39.483: %CELLWAN-2-BEARER_UP: Instance id=0, Default bearer (bearer_id=5) in Cellular0 is now UP
*Apr 1 16:18:39.483: Cellular0 profile 0, session ACTIVE
*Apr 1 16:18:39.483: cellwan_api_pkt_session_notify:connected idb_subunit:0
*Apr 1 16:18:39.723: cellwan_api_handle_profile_ip_addr_get_resp pdn 0 valid 1 length 4 session active 1, profile:0
*Apr 1 16:18:39.723: Sending ok response to line:3
*Apr 1 16:18:39.723: CHAT3: Completed match for expect: OK
*Apr 1 16:18:39.723: CHAT3: Chat script lte finished, status = Success
*Apr 1 16:18:39.723: TTY3: no timer type 1 to destroy
*Apr 1 16:18:39.723: TTY3: no timer type 0 to destroy
*Apr 1 16:18:39.723: TTY3: no timer type 2 to destroy.
*Apr 1 16:18:39.799: Cellular0 DirectIP: Primary DNS address 165.21.83.88 added
*Apr 1 16:18:39.799: Cellular0 DirectIP: Secondary DNS 165.21.100.88 added
*Apr 1 16:18:41.723: %LINK-3-UPDOWN: Interface Cellular0, changed state to up.!!! // WAIT 3 MINS FOR CELL 0 INTERFACE TO BE UP (SCANNING FOR CELL FREQUENCY)
Success rate is 60 percent (3/5), round-trip min/avg/max = 28/118/296 ms
Router#
*Apr 1 16:18:41.723: Ce0 DDR: Dialer statechange to up
*Apr 1 16:18:41.723: Ce0 DDR: Dialer call has been placed
*Apr 1 16:18:41.723: Cellular0 DirectIP: Install negotiated IP interface address 10.233.119.6
*Apr 1 16:18:41.723: Ce0 DDR: dialer protocol up
*Apr 1 16:18:42.723: %LINEPROTO-5-UPDOWN: Line protocol on Interface Cellular0, changed state to up
*Apr 1 16:18:43.671: TTY0: resume timer type 1 (OK)
Router#show cell 0 network
Current System Time = Fri Apr 1 16:20:2 2016
Current Service Status = Normal
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Network = SingTel
Mobile Country Code (MCC) = 525
Mobile Network Code (MNC) = 1
Packet switch domain(PS) state = Attached
Registration state(EMM) = Registered
EMM Sub State = Normal Service
Tracking Area Code (TAC) = 710
Cell ID = 190994691
Router#show cell 0 profile
Profile 1 = ACTIVE* **
--------
PDP Type = IPv4
PDP address = 10.233.119.6
Access Point Name (APN) = e-ideas
Authentication = CHAP
Username: 65ideas
Password: 65ideas
Primary DNS address = 165.21.83.88
Secondary DNS address = 165.21.100.88
* - Default profile
** - LTE attach profile
Configured default profile for active SIM 0 is profile 1.
Router#ping 8.8.8.8
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 28/84/300 ms
Router#show interface cell0
Cellular0 is up, line protocol is up
Hardware is 4G WWAN Modem - Global (Europe & Australia) Multimode LTE/DC-HSPA+/HSPA+/HSPA/U
Internet address is 10.233.119.6/32
MTU 1500 bytes, BW 50000 Kbit/sec, DLY 100000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation SLIP, loopback not set
Keepalive not supported
Time to interface disconnect: idle 00:00:58
Last input 00:01:01, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/10 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
9 packets input, 828 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
8 packets output, 800 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
Router#
*Apr 1 16:22:12.047: Ce0 DDR: idle timeout
*Apr 1 16:22:12.047: Ce0 DDR: disconnecting call
*Apr 1 16:22:12.047: TTY3: Async Int reset: Dropping DTR
*Apr 1 16:22:14.047: %LINK-5-CHANGED: Interface Cellular0, changed state to reset
*Apr 1 16:22:15.047: %LINEPROTO-5-UPDOWN: Line protocol on Interface Cellular0, changed state to down
*Apr 1 16:22:17.047: api_manage_packet_session Removing IP DNS profile:0 active_prof:0
*Apr 1 16:22:17.047: TTY3: no timer type 0 to destroy
*Apr 1 16:22:17.047: TTY3: no timer type 1 to destroy
*Apr 1 16:22:17.047: TTY3: no timer type 3 to destroy
*Apr 1 16:22:17.047: TTY3: no timer type 4 to destroy
*Apr 1 16:22:17.047: TTY3: no timer type 10 to destroy
*Apr 1 16:22:17.047: TTY3: no timer type 2 to destroy
*Apr 1 16:22:17.047: TTY3: Async Int cleanup: Restoring DTR
*Apr 1 16:22:17.047: Cellular0 DirectIP: Remove negotiated IP interface address
*Apr 1 16:22:17.047: Cellular0 DirectIP: Primary DNS address 165.21.83.88 removed
*Apr 1 16:22:17.047: Cellular0 DirectIP: Secondary DNS address 165.21.100.88 removed
*Apr 1 16:22:17.179: cellwan_api_pkt_session_notify: instance id:0 profile:0 status:0
*Apr 1 16:22:17.179: %CELLWAN-2-BEARER_DELETED: Instance id=0, Default bearer (bearer_id=5) in Cellular0 is now deleted.
*Apr 1 16:22:17.179: Cellular0 profile 0, session INACTIVE
*Apr 1 16:22:17.179: Cellular0 DirectIP: Remove negotiated IP interface address
*Apr 1 16:22:19.047: %LINK-3-UPDOWN: Interface Cellular0, changed state to down
*Apr 1 16:22:29.047: Ce0 DDR: re-enable timeout
Router#show interface cell0
Cellular0 is up (spoofing), line protocol is up (spoofing)
Hardware is 4G WWAN Modem - Global (Europe & Australia) Multimode LTE/DC-HSPA+/HSPA+/HSPA/U
Internet address will be assigned dynamically by the network // THE DHCP IP ADDRESS WAS REMOVED DUE TO IDLE TIMEOUT
MTU 1500 bytes, BW 9 Kbit/sec, DLY 100000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation SLIP, loopback not set
Keepalive not supported
Last input 00:02:35, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/10 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
9 packets input, 828 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
8 packets output, 800 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
Router(config)#interface cell0
Router(config-if)#dialer idle-timeout 0 // TO KEEP THE WWAN/CELL0 INTERFACE UP AND CONNECTED
Router#ping 8.8.8.8
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
*Apr 1 16:23:52.411: %CELLWAN-2-BEARER_UP: Instance id=0, Default bearer (bearer_id=5) in
Cellular0 is now UP.
*Apr 1 16:23:54.651: %LINK-3-UPDOWN: Interface Cellular0, changed state to up
*Apr 1 16:23:55.651: %LINEPROTO-5-UPDOWN: Line protocol on Interface Cellular0, changed state to up.!!!
Success rate is 60 percent (3/5), round-trip min/avg/max = 28/80/180 ms
Router#show interface cell0
Cellular0 is up, line protocol is up
Hardware is 4G WWAN Modem - Global (Europe & Australia) Multimode LTE/DC-HSPA+/HSPA+/HSPA/U
Internet address is 10.233.119.6/32
MTU 1500 bytes, BW 50000 Kbit/sec, DLY 100000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation SLIP, loopback not set
Keepalive not supported
Last input 00:01:14, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/10 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
13 packets input, 1156 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
11 packets output, 1100 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
Below is the basic working config. The LTE profile is not shown.
Router#show run
Building configuration...
Current configuration : 2546 bytes
!
! Last configuration change at 16:37:51 UTC Fri Apr 1 2016
!
version 15.5
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
enable password cisco
!
no aaa new-model
ethernet lmi ce
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
ip cef
no ipv6 cef
!
!
!
!
!
multilink bundle-name authenticated
!
!
chat-script lte "" "AT!CALL" TIMEOUT 20 "OK" // DEFAULT CONFIG
!
!
!
!
!
license udi pid C899G-LTE-GA-K9 sn FCZ20069123
!
!
username cisco privilege 15 password 0 cisco
!
!
!
!
!
controlle lte modem link-recovery rssi onset-threshold -110
lte modem link-recovery monitor-timer 20
lte modem link-recovery wait-timer 10
lte modem link-recovery debounce-count 6
!
!
!
!
!
!
!
!
!
!
!
!
interface Cellular0
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation slip
dialer in-band
dialer idle-timeout 0
dialer string lte // DEFAULT CONFIG
dialer-group 1
!
interface Cellular1
no ip address
encapsulation slip
!
interface FastEthernet0
no ip address
shutdown
duplex auto
speed auto
!
interface GigabitEthernet0
no ip address
!
interface GigabitEthernet1
no ip address
!
interface GigabitEthernet2
no ip address
!
interface GigabitEthernet3
no ip address
!
interface GigabitEthernet4
no ip address
!
interface GigabitEthernet5
no ip address
!
interface GigabitEthernet6
no ip address
!
interface GigabitEthernet7
no ip address
!
interface GigabitEthernet8
no ip address
shutdown
duplex auto
speed auto
!
interface GigabitEthernet9
no ip address
shutdown
duplex auto
speed auto
!
interface Vlan1
ip address 10.1.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
!
ip nat inside source list 1 interface Cellular0 overload
ip route 0.0.0.0 0.0.0.0 Cellular0
!
dialer-list 1 protocol ip permit
!
access-list 1 permit 10.1.1.0 0.0.0.255
!
control-plane
!
!
!
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
!
mgcp profile default
!
!
!
!
!
!
!
line con 0
password cisco
login
no modem enable
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
stopbits 1
line 3
script dialer lte // DEFAULT CONFIG
no exec
rxspeed 100000000 // DEFAULT CONFIG
txspeed 50000000 // DEFAULT CONFIG
line 8
no exec
rxspeed 100000000
txspeed 50000000
line vty 0 4
password cisco
login
transport input none
!
scheduler allocate 20000 1000
!
end
I got a 14 Mbps download / 22 Mbps upload Speedtest result from the PC connected (wired) behind the Cisco 4G router. I also tested using a 3G SIM card (used the same SingTel LTE/APN profile) which also worked and got almost the same Speedtest result.
Below are some helpful troubleshooting commands and remotely check router LED status.
Router#show platform led
LED STATUS:
==========
POWER : GREEN
PPP : OFF
POE OK : OFF
xDSL CD : OFF
xDSL DATA : OFF
VPN : OFF
ISDN B1 DATA : OFF
ISDN B2 DATA : OFF
RSSI : GREEN(2 BLINK)
GPS : OFF
SIM slot0 : GREEN
SIM slot1 : OFF
Service : GREEN(2 BLINK)
Router#show controller cellular 0
Interface Cellular0
4G WWAN Modem - Global (Europe & Australia) Multimode LTE/DC-HSPA+/HSPA+/HSPA/U
Cellular modem configuration
======================================
Modem is recognized as valid
manufacture id: 0x00001199 product id: 0x000068C0
Sierra Wireless Direct IP MC7304 modem
Modem Uplink Speed = 384 kbit.
Modem Downlink Speed = 384 kbit.
GPS Feature: enabled
GPS State: GPS disabled
GPS Mode: disabled
GPS Port selected: Dedicated GPS port
Cellular Dual SIM details:
---------------------------
SIM 0 is present
SIM 0 is active SIM
Cellular Dual SIM register:
Dual SIM Control Register 6A
Dual SIM Interrupt Register 4
Dual SIM Mask Interrupt Register C6
Modem Management Statistics
---------------------------
Modem resets = 12
Modem user initiated resets = 0
Modem user initiated power-cycles = 0
Modem timeouts = 10
Modem parameters at the last timeout:
SDK API return code was 50462720(0x3020000)
Link recovery is ON
Registration check is ON
RSSI threshold value is -110 dBm
Monitor Timer value is 20 seconds
Wait Timer value is 10 seconds
Debounce Count value is 6
Last known modem state = 'application' mode
AT Command Port = /dev/ttyUSB2
NMEA Port = /dev/ttyUSB1
DM Port = /dev/ttyUSB0
DIP MDM link status retry count = 0 pdp context = 0
DIP MDM link up pending = 0 pdp context = 0
DIP MDM link status retry count = 0 pdp context = 1
DIP MDM link up pending = 0 pdp context = 1
DIP MDM link status retry count = 0 pdp context = 2
DIP MDM link up pending = 0 pdp context = 2
IDB with pending DIP call: Cellular0
IDB Cellular0: DIP profile id = 1
IDB Cellular1: DIP profile id = 255
RSSI LED : 3-blink Green
Service LED : 2-blink Green
SIM LED : Slot0 - Green
GPS LED : Off
GPS NMEA port = Disabled (Stream OFF)
DM port = Disabled
Modem Callback Statistics
---------------------------
PacketServiceCallback_count 1
DataBearerCallback_count 0
DormancyStatusCallback_count 0
PowerCallback_count 0
ByteTotalsCallback_count 0
iByteTotalsCallback_count 0
PacketsCountCallback_count 0
iPacketsCountCallback_count 0
ActivationStatusCallback_count 0
MobileIPStatusCallback_count 0
RoamingIndicatorCallback_count 0
DataCapabilitiesCallback_count 0
SignalStrengthCallback_count 0
iSignalStrengthCallback_count 0
RFInfoCallback_count 0
LURejectCallback_count 0
NewSMSCallback_count 0
SLQSSMSEventCallback_count 0
NMEACallback_count 0
PDSStateCallback_count 1
CATEventCallback_count 0
iCATEventCallback_count 0
DeviceStateChangeCbk_count 0
FwDldCompletionCbk_count 0
SLQSOMADMAlertCallback_count 0
OMADMStateCallback_count 0
SLQSServingSystemCallback_count 1955
SLQSBandPreferenceCbk_count 0
USSDReleaseCallback_count 0
USSDNotificationCallback_count 0
SLQSSignalStrengthsCallback_count 0
iSLQSSignalStrengthsCallback_count 0
SLQSSDKTerminatedCallback_count 0
SLQSTransLayerInfoCallback_count 0
SLQSTransNWRegInfoCallback_count 0
SLQSSysSelectionPrefCallBack_count 0
NotifySessionStateDisconnect_count 0
WdsEventCallback_count 1679
HeartbeatModemStatisticsCallback_count 5905
0 input aborts on receiving flag sequence
0 throttles, 0 enables
0 overruns, 0 CRC errors
0 resource errors, 0 incomp frame errors
0 input drops
0 transmitter underruns
Cellular UBOOT F/W Info
========================
UBOOT Version = 2.0
UBOOT Build Date = Sep 21 2014
C800 Cellular Linux F/W Info
=============================
Linux Kernel:
Firmware Build Date = Nov 2 2016
Firmware Version = 2.0
Linux Rootfs:
Firmware Build Date = Nov 2 2016
Firmware Version = 2.0
The Current Modem SDK Version is 03.03.04.03
Modem USB-Serial Driver Version is GobiSerial <unknown>
Modem USB-Net Driver Version is GobiNet <unknown>
Cellular Statistics
===========================
IPC Counters
--------------------------------
IPC Tx :646094 IPC Rx AT commands :108
IPC Tx without Ack :646066 IPC Rx Mgmt & API :876099
IPC Tx with Ack :28 :
IPC Tx Err Invalid Sig :0 :
IPC Tx Err Q full :0 :
IPC Tx Err Q null pak :0 :
IPC Tx Err Q null bool :0 :
IPC Tx Err Bool Create fl:0 :
IPC Tx Err Ack Fail :0 :
IPC Tx Pending :0 :
IPC Buffers in Use :257 :
Data Counters
--------------------------------
Data Tx Packets :30764 Data Rx Packets :36307
Data Tx Bytes :5444613 Data Rx Bytes :36408144
Host Data Statistics from Linux
--------------------------------
Statistics for PDN 0:
Data Tx Packets :30764 Data Rx Packets :36307
IP pkts dropped :0
Statistics for PDN 1:
Data Tx Packets :0 Data Rx Packets :0
IP pkts dropped :0
MCC per channel information (MAX 9)
Core 0 Channel Bitmaps:
IOS: Tx Data Ready Bitmap 0x0, Tx Complete Bitmap 0x1FF
Core 0 Counters:
===================
[Chan 0]
============
Data Tx Packets No Partic:646094 Data Rx Packets :876271
Data Tx Bytes No Particle:12926942 Data Rx Bytes :72269497
Data Tx Packets Single Pa:0 :
Data Tx Bytes Single Part:0 :
Data Tx Packets Multi Par:0 :
Data Tx Bytes Multi Parti:0 :
Tx Errors :0 Rx Errors :0
[Chan 1]
============
Data Tx Packets No Partic:30764 Data Rx Packets :36371
Data Tx Bytes No Particle:5444613 Data Rx Bytes :36408144
Data Tx Packets Single Pa:0 :
Data Tx Bytes Single Part:0 :
Data Tx Packets Multi Par:0 :
Data Tx Bytes Multi Parti:0 :
Tx Errors :0 Rx Errors :0
[Chan 2]
============
Data Tx Packets No Partic:0 Data Rx Packets :64
Data Tx Bytes No Particle:0 Data Rx Bytes :0
Data Tx Packets Single Pa:0 :
Data Tx Bytes Single Part:0 :
Data Tx Packets Multi Par:0 :
Data Tx Bytes Multi Parti:0 :
Tx Errors :0 Rx Errors :0
[Chan 3]
============
Data Tx Packets No Partic:29890 Data Rx Packets :6
Data Tx Bytes No Particle:11565468 Data Rx Bytes :468
Data Tx Packets Single Pa:0 :
Data Tx Bytes Single Part:0 :
Data Tx Packets Multi Par:0 :
Data Tx Bytes Multi Parti:0 :
Tx Errors :0 Rx Errors :0
[Chan 4]
============
Data Tx Packets No Partic:0 Data Rx Packets :64
Data Tx Bytes No Particle:0 Data Rx Bytes :0
Data Tx Packets Single Pa:0 :
Data Tx Bytes Single Part:0 :
Data Tx Packets Multi Par:0 :
Data Tx Bytes Multi Parti:0 :
Tx Errors :0 Rx Errors :0
[Chan 5]
============
Data Tx Packets No Partic:0 Data Rx Packets :64
Data Tx Bytes No Particle:0 Data Rx Bytes :0
Data Tx Packets Single Pa:0 :
Data Tx Bytes Single Part:0 :
Data Tx Packets Multi Par:0 :
Data Tx Bytes Multi Parti:0 :
Tx Errors :0 Rx Errors :0
[Chan 6]
============
Data Tx Packets No Partic:0 Data Rx Packets :64
Data Tx Bytes No Particle:0 Data Rx Bytes :0
Data Tx Packets Single Pa:0 :
Data Tx Bytes Single Part:0 :
Data Tx Packets Multi Par:0 :
Data Tx Bytes Multi Parti:0 :
Tx Errors :0 Rx Errors :0
[Chan 7]
============
Data Tx Packets No Partic:0 Data Rx Packets :64
Data Tx Bytes No Particle:0 Data Rx Bytes :0
Data Tx Packets Single Pa:0 :
Data Tx Bytes Single Part:0 :
Data Tx Packets Multi Par:0 :
Data Tx Bytes Multi Parti:0 :
Tx Errors :0 Rx Errors :0
[Chan 8]
============
Data Tx Packets No Partic:0 Data Rx Packets :64
Data Tx Bytes No Particle:0 Data Rx Bytes :0
Data Tx Packets Single Pa:0 :
Data Tx Bytes Single Part:0 :
Data Tx Packets Multi Par:0 :
Data Tx Bytes Multi Parti:0 :
Tx Errors :0 Rx Errors :0
Core 0 TX Ring information:
==========================
[Chan 0] txring=0x17C00008, txr shadow=0x211E944C, tx_head=17, tx_tail=17, tandem_tail=49, tx_count=0
Core 0 Chan 0 TX ring entries:
Index TxR-Addr Buff-Addr Size Status
00 0x17C00008 0x0 00000 0x0000
01 0x17C00018 0x0 00000 0x0000
02 0x17C00028 0x0 00000 0x0000
03 0x17C00038 0x0 00000 0x0000
04 0x17C00048 0x0 00000 0x0000
05 0x17C00058 0x0 00000 0x0000
<OUTPUT TRUCATED>
