Here's a link in performing an IOS-XE upgrade in a Cisco 3650 Catalyst switch. This is also applicable to a Cisco 3850 since they share the same platform architecture. I had to upgrade a Cisco 3650 from IOS-XE 16.06.08 to 16.12.07.
Transfer the new IOS-XE to the switch flash memory.
3650#copy tftp://172.16.1.2/cat3k_caa-universalk9.16.12.07.SPA.bin flash
Destination filename [cat3k_caa-universalk9.16.12.07.SPA.bin]?
Accessing tftp://172.16.1.2/cat3k_caa-universalk9.16.12.07.SPA.bin...
Loading cat3k_caa-universalk9.16.12.07.SPA.bin from 172.16.1.2 (via Vlan10): !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
<OUTPUT TRUNCATED>
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
[OK - 480189009 bytes]
480189009 bytes copied in 1674.567 secs (286754 bytes/sec)
3650#dir
Directory of flash:/
38722 -rw- 83293932 Jun 30 2017 11:06:42 +00:00 cat3k_caa-base.SPA.03.06.06E.pkg
38723 -rw- 3982012 Jun 30 2017 11:06:43 +00:00 cat3k_caa-drivers.SPA.03.06.06E.pkg
38724 -rw- 33788908 Jun 30 2017 11:06:42 +00:00 cat3k_caa-infra.SPA.03.06.06E.pkg
38725 -rw- 43074880 Jun 30 2017 11:06:42 +00:00 cat3k_caa-iosd-universalk9.SPA.152-2.E6.pkg
38726 -rw- 28394380 Jun 30 2017 11:06:42 +00:00 cat3k_caa-platform.SPA.03.06.06E.pkg
38727 -rw- 111233856 Jun 30 2017 11:06:43 +00:00 cat3k_caa-wcm.SPA.10.2.160.0.pkg
38738 -rw- 34 Oct 5 2021 03:40:44 +00:00 pnp-tech-time
85185 drwx 4096 Jun 2 2022 02:23:24 +00:00 dc_profile_dir
38729 -rw- 2097152 Jun 14 2022 07:55:38 +00:00 nvram_config
38734 drwx 4096 Sep 24 2021 11:47:36 +00:00 core
38731 -rw- 15818 Feb 7 2018 11:43:00 +00:00 starr
38744 -rw- 19167872 Sep 24 2021 11:58:57 +00:00 cat3k_caa-guestshell.16.06.08.SPA.pkg
38732 drwx 4096 Jun 2 2022 02:23:07 +00:00 .installer
38733 -rw- 1147 Jun 2 2022 02:23:07 +00:00 bootloader_evt_handle.log
85187 drwx 4096 Sep 24 2021 12:07:52 +00:00 .prst_sync
7745 drwx 4096 Sep 24 2021 12:01:42 +00:00 .rollback_timer
15489 drwx 4096 Sep 24 2021 11:43:59 +00:00 gs_script
38735 -rw- 128103 Jun 2 2022 02:23:45 +00:00 memleak.tcl
38737 -rw- 2097152 Jun 14 2022 07:55:38 +00:00 nvram_config_bkup
38748 -rw- 30417560 Sep 24 2021 11:59:22 +00:00 cat3k_caa-rpbase.16.06.08.SPA.pkg
38745 -rw- 336503416 Sep 24 2021 11:59:19 +00:00 cat3k_caa-rpcore.16.06.08.SPA.pkg
38747 -rw- 5091968 Sep 24 2021 11:59:20 +00:00 cat3k_caa-srdriver.16.06.08.SPA.pkg
38746 -rw- 16271996 Sep 24 2021 11:59:20 +00:00 cat3k_caa-webui.16.06.08.SPA.pkg
38743 -rw- 4742 Sep 24 2021 12:00:14 +00:00 packages.conf
38728 -rw- 362 Sep 24 2021 12:01:55 +00:00 .packages.verify.log
38749 -rw- 66305 Oct 5 2021 03:40:48 +00:00 pnp-tech-discovery-summary
38750 -rw- 1936 Dec 2 2021 06:05:38 +00:00 vlan.dat
38751 -rw- 480189009 Jun 21 2022 03:22:07 +00:00 cat3k_caa-universalk9.16.12.07.SPA.bin
1621966848 bytes total (339550208 bytes free)
Use the request platform software package install switch macro command to expand and install the new IOS-XE package files.
3650#request platform software package install switch all file flash:cat3k_caa-universalk9.16.12.07.SPA.bin
--- Starting install local lock acquisition on switch 1 ---
Finished install local lock acquisition on switch 1
Expanding image file: flash:cat3k_caa-universalk9.16.12.07.SPA.bin
[1]: Expanding file
[1]: Finished expanding all-in-one software package in switch 1
SUCCESS: Finished expanding all-in-one software package.
[1]: Performing install
SUCCESS: install finished
[1]: install package(s) on switch 1
--- Starting list of software package changes ---
Old files list:
Removed cat3k_caa-guestshell.16.06.08.SPA.pkg
Removed cat3k_caa-rpbase.16.06.08.SPA.pkg
Removed cat3k_caa-rpcore.16.06.08.SPA.pkg
Removed cat3k_caa-srdriver.16.06.08.SPA.pkg
Removed cat3k_caa-webui.16.06.08.SPA.pkg
New files list:
Added cat3k_caa-guestshell.16.12.07.SPA.pkg
Added cat3k_caa-rpbase.16.12.07.SPA.pkg
Added cat3k_caa-rpcore.16.12.07.SPA.pkg
Added cat3k_caa-srdriver.16.12.07.SPA.pkg
Added cat3k_caa-webui.16.12.07.SPA.pkg
Finished list of software package changes
SUCCESS: Software provisioned. New software will load on reboot.
[1]: Finished install successful on switch 1
Checking status of install on [1]
[1]: Finished install in switch 1
SUCCESS: Finished install: Success on [1]
Make sure the boot variable and new provisioned files in packages.conf are correct.
3650#show boot
---------------------------
Switch 1
---------------------------
Current Boot Variables:
BOOT variable does not exist
Boot Variables on next reload:
BOOT variable = flash:packages.conf
Manual Boot = no
Enable Break = no
Boot Mode = DEVICE
iPXE Timeout = 0
3650#more flash:packages.conf
#! /usr/binos/bin/packages_conf.sh
sha1sum: 97b8f831ba81fcb9fa3234c6d9ab77402f1cc292
# sha1sum above - used to verify that this file is not corrupted.
#
# package.conf: provisioned software file for build 2022-02-02_07.35
#
# NOTE: Editing this file by hand is not recommended. It is generated
# as part of the build process, and is subject to boot-time
# consistency checks. Automatically-produced package files are
# guaranteed to pass those checks. Manually-maintained ones are
# not. Because "nfs" and "mount" directives are processed first,
# regardless of their position in the file, the recommended
# approach is to keep a separate file containing JUST your
# personal "nfs" and "mount" directives, and to append it to the
# automatically-generated file.
#
# Note further that when SHA-1 checksum verification is enabled,
# you will NOT be able to alter this file without updating the
# SHA-1 sum.
#
# This file can contain three types of entries:
#
#
# NFS directives (optional)
# notes: NFS directives are processed before all others (mount, iso).
# Multiple NFS directives may appear so long as they do not
# conflict -- that is, specify the same source or mountpoint.
# syntax: nfs <IP ADDRESS>:<REMOTE_PATH> <LOCAL_MOUNTPOINT>
# example: nfs 127.0.0.1:/auto/some/nfs/path /auto/some/nfs/path
#
#
# mount directives (optional)
# notes: mount directives are processed after 'nfs' and before 'iso'.
# One mount directive may appear for each F/S/B/P tuple
# syntax: mount FRU SLOT BAY PACKAGE_NAME LINUX_PATH
# example: mount rp 0 0 rp_base /auto/some/nfs/path/abs_soft/rp_base.ppc
#
# The specified LINUX_PATH may be local [sata disk] or
# reference the NFS mounts since they are processed first.
#
# Mount directives cause the package-specific mount link to
# be set to the specified path instead of to the mountpoint
# in sw for the corresponding ISO.
#
#
# iso directives (mandatory)
# notes: iso directives are processed last: any package for which
# a 'mount' directive does not appear will be mounted.
# One iso directive may appear for each F/S/B/P tuple.
# syntax: iso FRU SLOT BAY PACKAGE_NAME PACKAGE_FILE.bin
# example: iso rp 0 0 rp_base rp_base.ppc.bin
#
# PACKAGE_FILE.bin is a path relative to the packages.conf
# file. Although it supports sub-directories for development
# purposes, in deployment the files will always be managed
# as in the same directory as packages.conf so as to
# guarantee that name collisions cannot occur.
#
# Note that the RP 0/1 distinction is a convenience for development
# and testing as it allows us to have a packages.conf describe a
# SW load that varies depending on whether the RP finds itself in
# slot 0 or 1.
#
# The ISSU process *must* update *both* RP slots simultaneously so that
# the RP will behave predictably whichever slot it finds itself on [e.g.,
# if package X is upgraded, and the RP is ejected and put into either
# slot of a new chassis, we expect to see the upgraded X without regard
# to slot].
#
# This is for NOVA
iso rp 0 0 rp_base cat3k_caa-rpbase.16.12.07.SPA.pkg
iso rp 0 0 rp_core cat3k_caa-rpcore.16.12.07.SPA.pkg
iso rp 0 0 rp_daemons cat3k_caa-rpcore.16.12.07.SPA.pkg
iso rp 0 0 rp_iosd cat3k_caa-rpcore.16.12.07.SPA.pkg
iso rp 0 0 rp_webui cat3k_caa-webui.16.12.07.SPA.pkg
iso rp 0 0 srdriver cat3k_caa-srdriver.16.12.07.SPA.pkg
iso rp 0 0 rp_security cat3k_caa-rpcore.16.12.07.SPA.pkg
iso rp 0 0 guestshell cat3k_caa-guestshell.16.12.07.SPA.pkg
iso fp 0 0 fp cat3k_caa-rpcore.16.12.07.SPA.pkg
#
# -start- superpackage .pkginfo
#
# pkginfo: Name: rp_super
# pkginfo: BuildTime: 2022-02-02_07.35
# pkginfo: ReleaseDate: Wed-02-Feb-22-04:05
# pkginfo: .BuildArch: mips64
# pkginfo: BootArchitecture: mips
# pkginfo: .BootArch: mips
# pkginfo: RouteProcessor: edison
# pkginfo: Platform: CAT3K_CAA
# pkginfo: User: mcpre
# pkginfo: PackageName: universalk9
# pkginfo: Build: 16.12.07
# pkginfo: .SupportedBoards: edison
# pkginfo: .InstallModel:
# pkginfo: .PackageRole: rp_super
# pkginfo: .RestartRole: rp_super
# pkginfo: CardTypes:
# pkginfo: .CardTypes:
# pkginfo: .BuildPath: /nobackup/mcpre/release/BLD-V16_12_07_FC2/binos/linkfarm/stage-edison/hard/rp_super_universalk9.mips64
# pkginfo: .Version: 16.12.07.0.6565.1643816123..Gibraltar
# pkginfo: .InstallVersion: 1.0.0
# pkginfo: .InstallCapCommitSupport: yes
#
# -end- superpackage .pkginfo
#
3650#reload
Proceed with reload? [confirm] // HIT ENTER
<OUTPUT TRUNCATED>
3650#show version
Cisco IOS XE Software, Version 16.12.07
Cisco IOS Software [Gibraltar], Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Version 16.12.7, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2022 by Cisco Systems, Inc.
Compiled Wed 02-Feb-22 07:28 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2022 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
BOOTLDR: CAT3K_CAA Boot Loader (CAT3K_CAA-HBOOT-M) Version 3.56, RELEASE SOFTWARE (P)
3650 uptime is 1 hour, 11 minutes
Uptime for this control processor is 1 hour, 14 minutes
System returned to ROM by Power Failure or Unknown at 06:48:16 UTC Tue Jun 21 2022
System restarted at 06:52:55 UTC Tue Jun 21 2022
System image file is "flash:packages.conf"
Last reload reason: Power Failure or Unknown
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Technology Package License Information:
------------------------------------------------------------------------------
Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------------------
ipbasek9 Smart License ipbasek9
None Subscription Smart License None
Smart Licensing Status: UNREGISTERED/EVAL MODE
cisco WS-C3650-24PS (MIPS) processor (revision Q0) with 794816K/6147K bytes of memory.
Processor board ID FDO2124QABC
2 Virtual Ethernet interfaces
28 Gigabit Ethernet interfaces
2048K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
250456K bytes of Crash Files at crashinfo:.
1609272K bytes of Flash at flash:.
0K bytes of WebUI ODM Files at webui:.
Base Ethernet MAC Address : 40:01:7a:45:d1:23
Motherboard Assembly Number : 73-15899-07
Motherboard Serial Number : FDO21240XYZ
Model Revision Number : Q0
Motherboard Revision Number : A0
Model Number : WS-C3650-24PS
System Serial Number : FDO2124QABC
Switch Ports Model SW Version SW Image Mode
------ ----- ----- ---------- ---------- ----
* 1 28 WS-C3650-24PS 16.12.07 CAT3K_CAA-UNIVERSALK9 INSTALL
Configuration register is 0x102
-----
For a stack switch, use the auto-copy keyword to automatically copy and install the new IOS-XE .bin file from the master switch to members of the stack.
3650-STACK#request platform software package install switch all
file flash:cat3k_caa-universalk9.16.12.07.SPA.bin auto-copy
--- Starting install local lock acquisition on switch 2 ---
Finished install local lock acquisition on switch 2
Expanding image file: flash:cat3k_caa-universalk9.16.12.07.SPA.bin
[2]: Copying flash:cat3k_caa-universalk9.16.12.07.SPA.bin from switch 2 to switch 1
[1]: Finished copying to switch 1
[1 2]: Expanding file
[1 2]: Finished expanding all-in-one software package in switch 1 2
SUCCESS: Finished expanding all-in-one software package.
[1 2]: Performing install
SUCCESS: install finished
[1]: install package(s) on switch 1
--- Starting list of software package changes ---
Old files list:
Removed cat3k_caa-guestshell.16.06.08.SPA.pkg
Removed cat3k_caa-rpbase.16.06.08.SPA.pkg
Removed cat3k_caa-rpcore.16.06.08.SPA.pkg
Removed cat3k_caa-srdriver.16.06.08.SPA.pkg
Removed cat3k_caa-webui.16.06.08.SPA.pkg
New files list:
Added cat3k_caa-guestshell.16.12.07.SPA.pkg
Added cat3k_caa-rpbase.16.12.07.SPA.pkg
Added cat3k_caa-rpcore.16.12.07.SPA.pkg
Added cat3k_caa-srdriver.16.12.07.SPA.pkg
Added cat3k_caa-webui.16.12.07.SPA.pkg
Finished list of software package changes
SUCCESS: Software provisioned. New software will load on reboot.
[1]: Finished install successful on switch 1
[2]: install package(s) on switch 2
--- Starting list of software package changes ---
Old files list:
Removed cat3k_caa-guestshell.16.06.08.SPA.pkg
Removed cat3k_caa-rpbase.16.06.08.SPA.pkg
Removed cat3k_caa-rpcore.16.06.08.SPA.pkg
Removed cat3k_caa-srdriver.16.06.08.SPA.pkg
Removed cat3k_caa-webui.16.06.08.SPA.pkg
New files list:
Added cat3k_caa-guestshell.16.12.07.SPA.pkg
Added cat3k_caa-rpbase.16.12.07.SPA.pkg
Added cat3k_caa-rpcore.16.12.07.SPA.pkg
Added cat3k_caa-srdriver.16.12.07.SPA.pkg
Added cat3k_caa-webui.16.12.07.SPA.pkg
Finished list of software package changes
SUCCESS: Software provisioned. New software will load on reboot.
[2]: Finished install successful on switch 2
Checking status of install on [1 2]
[1 2]: Finished install in switch 1 2
SUCCESS: Finished install: Success on [1 2]
3650-STACK#reload
Proceed with reload? [confirm] // HIT ENTER
<OUTPUT TRUNCATED>
3650-STACK#show version
Cisco IOS XE Software, Version 16.12.07
Cisco IOS Software [Gibraltar], Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Version 16.12.7, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2022 by Cisco Systems, Inc.
Compiled Wed 02-Feb-22 07:28 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2022 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
BOOTLDR: CAT3K_CAA Boot Loader (CAT3K_CAA-HBOOT-M) Version 4.66, RELEASE SOFTWARE (P)
3650-STACK uptime is 18 hours, 53 minutes
Uptime for this control processor is 18 hours, 57 minutes
System returned to ROM by Power Failure or Unknown at 07:41:07 UTC Tue Jun 21 2022
System restarted at 07:46:56 UTC Tue Jun 21 2022
System image file is "flash:packages.conf"
Last reload reason: Power Failure or Unknown
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Technology Package License Information:
------------------------------------------------------------------------------
Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------------------
ipbasek9 Smart License ipbasek9
None Subscription Smart License None
Smart Licensing Status: UNREGISTERED/EVAL MODE
cisco WS-C3650-24PS (MIPS) processor (revision G0) with 794816K/6147K bytes of memory.
Processor board ID FDO1827QABC
2 Virtual Ethernet interfaces
56 Gigabit Ethernet interfaces
2048K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
257008K bytes of Crash Files at crashinfo:.
252000K bytes of Crash Files at crashinfo-1:.
1550272K bytes of Flash at flash:.
1611414K bytes of Flash at flash-1:.
0K bytes of WebUI ODM Files at webui:.
Base Ethernet MAC Address : 54:a2:74:1a:71:23
Motherboard Assembly Number : 73-15128-05
Motherboard Serial Number : FDO1826QXYZ
Model Revision Number : G0
Motherboard Revision Number : A0
Model Number : WS-C3650-24PS
System Serial Number : FDO1827QABC
Switch Ports Model SW Version SW Image Mode
------ ----- ----- ---------- ---------- ----
1 28 WS-C3650-24PS 16.12.07 CAT3K_CAA-UNIVERSALK9 INSTALL
* 2 28 WS-C3650-24PS 16.12.07 CAT3K_CAA-UNIVERSALK9 INSTALL
Switch 01
---------
Switch uptime : 18 hours, 57 minutes
Base Ethernet MAC Address : 00:ea:bd:a9:34:56
Motherboard Assembly Number : 73-15899-07
Motherboard Serial Number : FDO22311456
Model Revision Number : S0
Motherboard Revision Number : A0
Model Number : WS-C3650-24PS
System Serial Number : FDO2232IDEF
Last reload reason : Reload Command
Configuration register is 0x102
If you encounter an issue in the expansion and installation of package files failed in a member of a stacked switch, check the contents of flash-1 and flash-2.
3650-STACK#request platform software package install switch all file flash:cat3k_caa-universalk9.16.12.07.SPA.bin auto-copy
--- Starting install local lock acquisition on switch 1 ---
Finished install local lock acquisition on switch 1
Expanding image file: flash:cat3k_caa-universalk9.16.12.07.SPA.bin
[1]: Copying flash:cat3k_caa-universalk9.16.12.07.SPA.bin from switch 1 to switch 2
[2]: Finished copying to switch 2
[1 2]: Expanding file
[1 2]: Finished expanding all-in-one software package in switch 1 2
SUCCESS: Finished expanding all-in-one software package.
[1 2]: Performing install
SUCCESS: install finished
[1]: install package(s) on switch 1
--- Starting list of software package changes ---
Old files list:
Removed cat3k_caa-guestshell.16.06.08.SPA.pkg
Removed cat3k_caa-rpbase.16.06.08.SPA.pkg
Removed cat3k_caa-rpcore.16.06.08.SPA.pkg
Removed cat3k_caa-srdriver.16.06.08.SPA.pkg
Removed cat3k_caa-webui.16.06.08.SPA.pkg
New files list:
Added cat3k_caa-guestshell.16.12.07.SPA.pkg
Added cat3k_caa-rpbase.16.12.07.SPA.pkg
Added cat3k_caa-rpcore.16.12.07.SPA.pkg
Added cat3k_caa-srdriver.16.12.07.SPA.pkg
Added cat3k_caa-webui.16.12.07.SPA.pkg
Finished list of software package changes
SUCCESS: Software provisioned. New software will load on reboot.
[1]: Finished install successful on switch 1
[2]: install package(s) on switch 2
--- Starting local lock acquisition on switch 2 ---
Finished local lock acquisition on switch 2
--- Starting file path checking ---
Finished file path checking
--- Starting image file verification ---
Checking image file names
Locating image files and validating name syntax
Found cat3k_caa-guestshell.16.12.07.SPA.pkg
Found cat3k_caa-rpbase.16.12.07.SPA.pkg
Found cat3k_caa-rpcore.16.12.07.SPA.pkg
Found cat3k_caa-srdriver.16.12.07.SPA.pkg
Found cat3k_caa-webui.16.12.07.SPA.pkg
Inspecting image file types
WARNING: In-service installation of RP Base package
WARNING: requires software reboot of target RP
WARNING: Automatically setting the on-reboot flag
WARNING: In-service installation of guestshell package
WARNING: requires software reboot of target
Processing image file constraints
Creating candidate provisioning file
Finished image file verification
--- Starting candidate package set construction ---
Verifying existing software set
FAILED: Invalid directory: /tmp/sw/mount/cat3k_caa-webui.16.06.08.SPA.pkg
[2]: Finished install failed on switch 2
Checking status of install on [1 2]
[1]: Finished install in switch 1
[2]: FAILED: install failed in switch 2
SUCCESS: Finished install: Success on [1]. Failed on [2]
3650-STACK#dir flash-1:
Directory of flash:/
7763 -rw- 2097152 Jun 21 2022 11:57:38 +00:00 nvram_config
7748 -rw- 6521532 Apr 2 2015 15:44:09 +00:00 cat3k_caa-drivers.SPA.03.03.04SE.pkg
7750 -rw- 34856268 Apr 2 2015 15:44:08 +00:00 cat3k_caa-iosd-universalk9.SPA.150-1.EZ4.pkg
7751 -rw- 25172880 Apr 2 2015 15:44:08 +00:00 cat3k_caa-platform.SPA.03.03.04SE.pkg
7752 -rw- 77445952 Apr 2 2015 15:44:09 +00:00 cat3k_caa-wcm.SPA.10.1.140.0.pkg
7754 -rw- 76 Jun 2 2022 02:24:17 +00:00 boothelper.log
61956 drwx 4096 Sep 24 2021 12:35:54 +00:00 core
61965 -rw- 19167872 Sep 24 2021 12:45:37 +00:00 cat3k_caa-guestshell.16.06.08.SPA.pkg
61955 drwx 4096 Jun 21 2022 07:59:25 +00:00 .installer
69700 drwx 4096 Sep 24 2021 12:55:02 +00:00 .prst_sync
23233 drwx 4096 Jun 2 2022 02:24:14 +00:00 dc_profile_dir
30978 drwx 4096 May 1 2015 07:52:45 +00:00 wnweb_store
7756 -rw- 1295 Jun 2 2022 02:23:57 +00:00 bootloader_evt_handle.log
77442 drwx 4096 Sep 24 2021 12:48:25 +00:00 .rollback_timer
77443 drwx 4096 Sep 24 2021 12:31:53 +00:00 gs_script
7757 -rw- 128103 Jun 2 2022 02:24:35 +00:00 memleak.tcl
7758 -rw- 34 Oct 6 2021 04:47:23 +00:00 pnp-tech-time
7759 -rw- 2097152 Jun 21 2022 11:57:39 +00:00 nvram_config_bkup
61969 -rw- 30417560 Sep 24 2021 12:46:01 +00:00 cat3k_caa-rpbase.16.06.08.SPA.pkg
61966 -rw- 336503416 Sep 24 2021 12:45:58 +00:00 cat3k_caa-rpcore.16.06.08.SPA.pkg
61968 -rw- 5091968 Sep 24 2021 12:46:00 +00:00 cat3k_caa-srdriver.16.06.08.SPA.pkg
61967 -rw- 16271996 Sep 24 2021 12:45:59 +00:00 cat3k_caa-webui.16.06.08.SPA.pkg
7766 -rw- 4780 Jun 21 2022 14:16:35 +00:00 packages.conf
7753 -rw- 460 Sep 24 2021 12:48:38 +00:00 .packages.verify.log
7761 -rw- 61107 Oct 6 2021 04:47:37 +00:00 pnp-tech-discovery-summary
7762 -rw- 1936 Jun 1 2022 01:10:18 +00:00 vlan.dat
7746 drwx 4096 Dec 2 2021 23:05:31 +00:00 onep
7775 -rw- 0 Jun 21 2022 08:00:39 +00:00 .onreboot
7770 -rw- 20097668 Jun 21 2022 07:58:37 +00:00 cat3k_caa-guestshell.16.12.07.SPA.pkg
7774 -rw- 32795564 Jun 21 2022 07:58:46 +00:00 cat3k_caa-rpbase.16.12.07.SPA.pkg
7773 -rw- 400857724 Jun 21 2022 07:58:43 +00:00 cat3k_caa-rpcore.16.12.07.SPA.pkg
7772 -rw- 3414660 Jun 21 2022 07:58:46 +00:00 cat3k_caa-srdriver.16.12.07.SPA.pkg
7769 -rw- 4780 Jun 21 2022 07:59:24 +00:00 cat3k_caa-universalk9.16.12.07.SPA.conf
7771 -rw- 23018112 Jun 21 2022 07:58:45 +00:00 cat3k_caa-webui.16.12.07.SPA.pkg
7767 -rw- 4742 Jun 21 2022 08:00:28 +00:00 packages.conf.00-
1621966848 bytes total (499437568 bytes free)
Member Switch 2 has the expanded 16.12.0.7 package files.
3650-STACK#dir flash-2:
Directory of flash-2:/
38753 -rw- 2097152 Jun 21 2022 11:57:40 +00:00 nvram_config
38762 -rw- 32795564 Jun 21 2022 14:16:08 +00:00 cat3k_caa-rpbase.16.12.07.SPA.pkg
38723 -rw- 5 Jun 21 2022 14:17:27 +00:00 .issu_loc_lock
38730 -rw- 4780 Jun 21 2022 11:46:59 +00:00 cat3k_caa-universalk9.16.12.07.SPA.1.conf
38727 -rw- 4780 Jun 21 2022 12:59:49 +00:00 cat3k_caa-universalk9.16.12.07.SPA.2.conf
38729 -rw- 76 Jun 2 2022 02:24:17 +00:00 boothelper.log
38732 drwx 4096 May 5 2015 09:45:44 +00:00 virtual-instance
38735 drwx 4096 Sep 24 2021 12:44:13 +00:00 core
38755 -rw- 20097668 Jun 21 2022 14:15:24 +00:00 cat3k_caa-guestshell.16.12.07.SPA.pkg
77441 drwx 4096 May 5 2015 09:45:44 +00:00 vman_fdb
38751 drwx 4096 Oct 6 2021 05:00:30 +00:00 onep
85186 drwx 4096 Jun 2 2022 02:24:15 +00:00 dc_profile_dir
85188 drwx 4096 Mar 28 2017 20:29:45 +00:00 wnweb_store
38747 -rw- 19167872 Sep 24 2021 12:56:02 +00:00 cat3k_caa-guestshell.16.06.08.SPA.pkg
38733 drwx 4096 Jun 21 2022 07:59:50 +00:00 .installer
38734 -rw- 1147 Jun 2 2022 02:23:58 +00:00 bootloader_evt_handle.log
38736 drwx 4096 Sep 24 2021 13:05:19 +00:00 .prst_sync
14 drwx 4096 Sep 24 2021 12:58:49 +00:00 .rollback_timer
7747 drwx 4096 Sep 24 2021 12:40:09 +00:00 gs_script
38737 -rw- 128103 Jun 2 2022 02:24:36 +00:00 memleak.tcl
38738 -rw- 35 Sep 24 2021 13:15:06 +00:00 pnp-tech-time
38740 -rw- 2097152 Jun 21 2022 11:57:41 +00:00 nvram_config_bkup
38749 -rw- 30417560 Sep 24 2021 12:56:26 +00:00 cat3k_caa-rpbase.16.06.08.SPA.pkg
38757 -rw- 400857724 Jun 21 2022 14:15:57 +00:00 cat3k_caa-rpcore.16.12.07.SPA.pkg
77443 -rw- 5091968 Sep 24 2021 12:56:24 +00:00 cat3k_caa-srdriver.16.06.08.SPA.pkg
38756 -rw- 23018112 Jun 21 2022 14:15:59 +00:00 cat3k_caa-webui.16.12.07.SPA.pkg
38746 -rw- 4742 Sep 24 2021 12:56:57 +00:00 packages.conf // FROM 16.06.08
38750 -rw- 460 Sep 24 2021 12:59:02 +00:00 .packages.verify.log
38741 -rw- 62276 Sep 24 2021 13:15:09 +00:00 pnp-tech-discovery-summary
38722 -rw- 1936 Jun 2 2022 02:31:17 +00:00 vlan.dat
38758 -rw- 3414660 Jun 21 2022 14:15:59 +00:00 cat3k_caa-srdriver.16.12.07.SPA.pkg
38754 -rw- 4780 Jun 21 2022 07:59:49 +00:00 cat3k_caa-universalk9.16.12.07.SPA.conf
38731 -rw- 4780 Jun 21 2022 13:38:24 +00:00 cat3k_caa-universalk9.16.12.07.SPA.3.conf
38728 -rw- 4780 Jun 21 2022 14:16:44 +00:00 cat3k_caa-universalk9.16.12.07.SPA.4.conf
1622147072 bytes total (660078592 bytes free)
Master Stack Switch 1 has the correct package files for the new IOS-XE 16.12.07.
3650-STACK#more flash-1:packages.conf
#! /usr/binos/bin/packages_conf.sh
sha1sum: 97b8f831ba81fcb9fa3234c6d9ab77402f1cc292
# sha1sum above - used to verify that this file is not corrupted.
#
# package.conf: provisioned software file for build 2022-02-02_07.35
#
# NOTE: Editing this file by hand is not recommended. It is generated
# as part of the build process, and is subject to boot-time
# consistency checks. Automatically-produced package files are
# guaranteed to pass those checks. Manually-maintained ones are
# not. Because "nfs" and "mount" directives are processed first,
# regardless of their position in the file, the recommended
# approach is to keep a separate file containing JUST your
# personal "nfs" and "mount" directives, and to append it to the
# automatically-generated file.
#
# Note further that when SHA-1 checksum verification is enabled,
# you will NOT be able to alter this file without updating the
# SHA-1 sum.
#
# This file can contain three types of entries:
#
#
# NFS directives (optional)
# notes: NFS directives are processed before all others (mount, iso).
# Multiple NFS directives may appear so long as they do not
# conflict -- that is, specify the same source or mountpoint.
# syntax: nfs <IP ADDRESS>:<REMOTE_PATH> <LOCAL_MOUNTPOINT>
# example: nfs 127.0.0.1:/auto/some/nfs/path /auto/some/nfs/path
#
#
# mount directives (optional)
# notes: mount directives are processed after 'nfs' and before 'iso'.
# One mount directive may appear for each F/S/B/P tuple
# syntax: mount FRU SLOT BAY PACKAGE_NAME LINUX_PATH
# example: mount rp 0 0 rp_base /auto/some/nfs/path/abs_soft/rp_base.ppc
#
# The specified LINUX_PATH may be local [sata disk] or
# reference the NFS mounts since they are processed first.
#
# Mount directives cause the package-specific mount link to
# be set to the specified path instead of to the mountpoint
# in sw for the corresponding ISO.
#
#
# iso directives (mandatory)
# notes: iso directives are processed last: any package for which
# a 'mount' directive does not appear will be mounted.
# One iso directive may appear for each F/S/B/P tuple.
# syntax: iso FRU SLOT BAY PACKAGE_NAME PACKAGE_FILE.bin
# example: iso rp 0 0 rp_base rp_base.ppc.bin
#
# PACKAGE_FILE.bin is a path relative to the packages.conf
# file. Although it supports sub-directories for development
# purposes, in deployment the files will always be managed
# as in the same directory as packages.conf so as to
# guarantee that name collisions cannot occur.
#
# Note that the RP 0/1 distinction is a convenience for development
# and testing as it allows us to have a packages.conf describe a
# SW load that varies depending on whether the RP finds itself in
# slot 0 or 1.
#
# The ISSU process *must* update *both* RP slots simultaneously so that
# the RP will behave predictably whichever slot it finds itself on [e.g.,
# if package X is upgraded, and the RP is ejected and put into either
# slot of a new chassis, we expect to see the upgraded X without regard
# to slot].
#
# This is for NOVA
iso rp 0 0 rp_base cat3k_caa-rpbase.16.12.07.SPA.pkg
iso rp 0 0 rp_core cat3k_caa-rpcore.16.12.07.SPA.pkg
iso rp 0 0 rp_daemons cat3k_caa-rpcore.16.12.07.SPA.pkg
iso rp 0 0 rp_iosd cat3k_caa-rpcore.16.12.07.SPA.pkg
iso rp 0 0 rp_webui cat3k_caa-webui.16.12.07.SPA.pkg
iso rp 0 0 srdriver cat3k_caa-srdriver.16.12.07.SPA.pkg
iso rp 0 0 rp_security cat3k_caa-rpcore.16.12.07.SPA.pkg
iso rp 0 0 guestshell cat3k_caa-guestshell.16.12.07.SPA.pkg
iso fp 0 0 fp cat3k_caa-rpcore.16.12.07.SPA.pkg
<OUTPUT TRUNCATED>
Member Stack Switch 2 packages.conf still points to the old 16.0.6.08 package files.
3650-STACK#more flash-2:packages.conf
#! /usr/binos/bin/packages_conf.sh
sha1sum: 2c6e83b4507769bcf744481fed36f131d593dbf8
# sha1sum above - used to verify that this file is not corrupted.
#
# package.conf: provisioned software file for build 2020-04-23_17.50
#
# NOTE: Editing this file by hand is not recommended. It is generated
# as part of the build process, and is subject to boot-time
# consistency checks. Automatically-produced package files are
# guaranteed to pass those checks. Manually-maintained ones are
# not. Because "nfs" and "mount" directives are processed first,
# regardless of their position in the file, the recommended
# approach is to keep a separate file containing JUST your
# personal "nfs" and "mount" directives, and to append it to the
# automatically-generated file.
#
# Note further that when SHA-1 checksum verification is enabled,
# you will NOT be able to alter this file without updating the
# SHA-1 sum.
#
# This file can contain three types of entries:
#
#
# NFS directives (optional)
# notes: NFS directives are processed before all others (mount, iso).
# Multiple NFS directives may appear so long as they do not
# conflict -- that is, specify the same source or mountpoint.
# syntax: nfs <IP ADDRESS>:<REMOTE_PATH> <LOCAL_MOUNTPOINT>
# example: nfs 127.0.0.1:/auto/some/nfs/path /auto/some/nfs/path
#
#
# mount directives (optional)
# notes: mount directives are processed after 'nfs' and before 'iso'.
# One mount directive may appear for each F/S/B/P tuple
# syntax: mount FRU SLOT BAY PACKAGE_NAME LINUX_PATH
# example: mount rp 0 0 rp_base /auto/some/nfs/path/abs_soft/rp_base.ppc
#
# The specified LINUX_PATH may be local [sata disk] or
# reference the NFS mounts since they are processed first.
#
# Mount directives cause the package-specific mount link to
# be set to the specified path instead of to the mountpoint
# in sw for the corresponding ISO.
#
#
# iso directives (mandatory)
# notes: iso directives are processed last: any package for which
# a 'mount' directive does not appear will be mounted.
# One iso directive may appear for each F/S/B/P tuple.
# syntax: iso FRU SLOT BAY PACKAGE_NAME PACKAGE_FILE.bin
# example: iso rp 0 0 rp_base rp_base.ppc.bin
#
# PACKAGE_FILE.bin is a path relative to the packages.conf
# file. Although it supports sub-directories for development
# purposes, in deployment the files will always be managed
# as in the same directory as packages.conf so as to
# guarantee that name collisions cannot occur.
#
# Note that the RP 0/1 distinction is a convenience for development
# and testing as it allows us to have a packages.conf describe a
# SW load that varies depending on whether the RP finds itself in
# slot 0 or 1.
#
# The ISSU process *must* update *both* RP slots simultaneously so that
# the RP will behave predictably whichever slot it finds itself on [e.g.,
# if package X is upgraded, and the RP is ejected and put into either
# slot of a new chassis, we expect to see the upgraded X without regard
# to slot].
#
iso rp 0 0 rp_base cat3k_caa-rpbase.16.06.08.SPA.pkg
iso rp 0 0 rp_core cat3k_caa-rpcore.16.06.08.SPA.pkg
iso rp 0 0 rp_daemons cat3k_caa-rpcore.16.06.08.SPA.pkg
iso rp 0 0 rp_iosd cat3k_caa-rpcore.16.06.08.SPA.pkg
iso rp 0 0 rp_webui cat3k_caa-webui.16.06.08.SPA.pkg
iso rp 0 0 srdriver cat3k_caa-srdriver.16.06.08.SPA.pkg
iso rp 0 0 rp_security cat3k_caa-rpcore.16.06.08.SPA.pkg
iso rp 0 0 guestshell cat3k_caa-guestshell.16.06.08.SPA.pkg
iso fp 0 0 fp cat3k_caa-rpcore.16.06.08.SPA.pkg
Just rename packages.conf in flash-2:
3650-STACK#rename flash-2:packages.conf flash-2:packages-old.conf // 16.06.08
Destination filename [packages-old.conf]?
3650-STACK#rename flash-2:cat3k_caa-universalk9.16.12.07.SPA.conf flash-2:packages.conf
Destination filename [packages.conf]?
Take note of the time stamps and file size. The packges-old.conf is from 16.06.08 which dates Sep 24 2021.
3650-STACK#dir flash-2:
Directory of flash-2:/
38753 -rw- 2097152 Jun 21 2022 11:57:40 +00:00 nvram_config
38762 -rw- 32795564 Jun 21 2022 14:16:08 +00:00 cat3k_caa-rpbase.16.12.07.SPA.pkg
38723 -rw- 5 Jun 21 2022 14:17:27 +00:00 .issu_loc_lock
38746
-rw- 4742 Sep 24 2021 12:56:57 +00:00 packages-old.conf // 16.06.08
38730 -rw- 4780 Jun 21 2022 11:46:59 +00:00 cat3k_caa-universalk9.16.12.07.SPA.1.conf
38754
-rw- 4780 Jun 21 2022 07:59:49 +00:00 packages.conf // 16.12.07
38727 -rw- 4780 Jun 21 2022 12:59:49 +00:00 cat3k_caa-universalk9.16.12.07.SPA.2.conf
38729 -rw- 76 Jun 2 2022 02:24:17 +00:00 boothelper.log
38732 drwx 4096 May 5 2015 09:45:44 +00:00 virtual-instance
38735 drwx 4096 Sep 24 2021 12:44:13 +00:00 core
38755 -rw- 20097668 Jun 21 2022 14:15:24 +00:00 cat3k_caa-guestshell.16.12.07.SPA.pkg
77441 drwx 4096 May 5 2015 09:45:44 +00:00 vman_fdb
38751 drwx 4096 Oct 6 2021 05:00:30 +00:00 onep
85186 drwx 4096 Jun 2 2022 02:24:15 +00:00 dc_profile_dir
85188 drwx 4096 Mar 28 2017 20:29:45 +00:00 wnweb_store
38747 -rw- 19167872 Sep 24 2021 12:56:02 +00:00 cat3k_caa-guestshell.16.06.08.SPA.pkg
38733 drwx 4096 Jun 21 2022 07:59:50 +00:00 .installer
38734 -rw- 1147 Jun 2 2022 02:23:58 +00:00 bootloader_evt_handle.log
38736 drwx 4096 Sep 24 2021 13:05:19 +00:00 .prst_sync
14 drwx 4096 Sep 24 2021 12:58:49 +00:00 .rollback_timer
7747 drwx 4096 Sep 24 2021 12:40:09 +00:00 gs_script
38737 -rw- 128103 Jun 2 2022 02:24:36 +00:00 memleak.tcl
38738 -rw- 35 Sep 24 2021 13:15:06 +00:00 pnp-tech-time
38740 -rw- 2097152 Jun 21 2022 11:57:41 +00:00 nvram_config_bkup
38749 -rw- 30417560 Sep 24 2021 12:56:26 +00:00 cat3k_caa-rpbase.16.06.08.SPA.pkg
38757 -rw- 400857724 Jun 21 2022 14:15:57 +00:00 cat3k_caa-rpcore.16.12.07.SPA.pkg
77443 -rw- 5091968 Sep 24 2021 12:56:24 +00:00 cat3k_caa-srdriver.16.06.08.SPA.pkg
38756 -rw- 23018112 Jun 21 2022 14:15:59 +00:00 cat3k_caa-webui.16.12.07.SPA.pkg
38750 -rw- 460 Sep 24 2021 12:59:02 +00:00 .packages.verify.log
38741 -rw- 62276 Sep 24 2021 13:15:09 +00:00 pnp-tech-discovery-summary
38722 -rw- 1936 Jun 2 2022 02:31:17 +00:00 vlan.dat
38758 -rw- 3414660 Jun 21 2022 14:15:59 +00:00 cat3k_caa-srdriver.16.12.07.SPA.pkg
38731 -rw- 4780 Jun 21 2022 13:38:24 +00:00 cat3k_caa-universalk9.16.12.07.SPA.3.conf
38728 -rw- 4780 Jun 21 2022 14:16:44 +00:00 cat3k_caa-universalk9.16.12.07.SPA.4.conf
1622147072 bytes total (660078592 bytes free)
The newly renamed packages.conf now correctly points to 16.12.07 packages files.
3650-STACK#more flash-2:packages.conf | begin for NOVA
# This is for NOVA
iso rp 0 0 rp_base cat3k_caa-rpbase.16.12.07.SPA.pkg
iso rp 0 0 rp_core cat3k_caa-rpcore.16.12.07.SPA.pkg
iso rp 0 0 rp_daemons cat3k_caa-rpcore.16.12.07.SPA.pkg
iso rp 0 0 rp_iosd cat3k_caa-rpcore.16.12.07.SPA.pkg
iso rp 0 0 rp_webui cat3k_caa-webui.16.12.07.SPA.pkg
iso rp 0 0 srdriver cat3k_caa-srdriver.16.12.07.SPA.pkg
iso rp 0 0 rp_security cat3k_caa-rpcore.16.12.07.SPA.pkg
iso rp 0 0 guestshell cat3k_caa-guestshell.16.12.07.SPA.pkg
iso fp 0 0 fp cat3k_caa-rpcore.16.12.07.SPA.pkg
You can now issue a reload at this point.
3650-STACK#show version
Cisco IOS XE Software, Version 16.12.07
Cisco IOS Software [Gibraltar], Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Version 16.12.7, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2022 by Cisco Systems, Inc.
Compiled Wed 02-Feb-22 07:28 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2022 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
BOOTLDR: CAT3K_CAA Boot Loader (CAT3K_CAA-HBOOT-M) Version 4.66, RELEASE SOFTWARE (P)
3650-STACK uptime is 15 hours, 18 minutes
Uptime for this control processor is 15 hours, 22 minutes
System returned to ROM by Power Failure or Unknown at 12:47:47 UTC Thu Jun 23 2022
System restarted at 12:52:52 UTC Thu Jun 23 2022
System image file is "flash:packages.conf"
Last reload reason: Power Failure or Unknown
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Technology Package License Information:
------------------------------------------------------------------------------
Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------------------
ipbasek9 Smart License ipbasek9
None Subscription Smart License None
Smart Licensing Status: UNREGISTERED/EVAL MODE
cisco WS-C3650-48PS (MIPS) processor (revision D0) with 794816K/6147K bytes of memory.
Processor board ID FDO1911EDEF
2 Virtual Ethernet interfaces
104 Gigabit Ethernet interfaces
2048K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
250456K bytes of Crash Files at crashinfo:.
250456K bytes of Crash Files at crashinfo-2:.
1609272K bytes of Flash at flash:.
1609272K bytes of Flash at flash-2:.
0K bytes of WebUI ODM Files at webui:.
Base Ethernet MAC Address : b0:aa:77:91:27:89
Motherboard Assembly Number : 73-15131-05
Motherboard Serial Number : FDO19110GHI
Model Revision Number : D0
Motherboard Revision Number : A0
Model Number : WS-C3650-48PS
System Serial Number : FDO1911EJKL
Switch Ports Model SW Version SW Image Mode
------ ----- ----- ---------- ---------- ----
* 1 52 WS-C3650-48PS 16.12.07 CAT3K_CAA-UNIVERSALK9 INSTALL
2 52 WS-C3650-48PS 16.12.07 CAT3K_CAA-UNIVERSALK9 INSTALL
Switch 02
---------
Switch uptime : 15 hours, 22 minutes
Base Ethernet MAC Address : b0:aa:77:aa:4:56
Motherboard Assembly Number : 73-15131-05
Motherboard Serial Number : FDO19110JKL
Model Revision Number : D0
Motherboard Revision Number : A0
Model Number : WS-C3650-48PS
System Serial Number : FDO1911EMNO
Last reload reason : Reload Command
Configuration register is 0x102
No comments:
Post a Comment